Forum Post: RE: idle-channel noise of ADS62C17
Hi, Matt;Yes, we use ADI's ADA4930 in front of the ADCs as ADC drivers. The low frequency noise may be from the jumper's bad connect which we use to switch different singal source. I will check it and...
View ArticleForum Post: RE: Reading streamed data ldc1000evm using c sharp
Hi Jonathan,Are you stopping the data stream before changing the sampling rate? You will have alignment issues if the sampling rate were changed during a data stream.Thanks,
View ArticleForum Post: DAC34SH84EVM
Support,Out customer is looking for an EVM with the DAC34SH84 on it. The schematic for the DAC34SH84EVM has the DAC34H84 device. Is there an EVM with the DAC34SH84?Thanks for your help.Regards,John...
View ArticleForum Post: RE: TVP5150 interrupt reset
Thank you very much!But any way, I only want to make the new settings of brightness to be available, if hardware reset pin can not used, can it be realized by software?
View ArticleForum Post: RE: TLV320AIC3100 linux driver
Im developing a new platform which includes am3352 and tlv320aic3100 codec, Im using linux-3.2.0-psp04.06.00.11. The kernel has ALSA which has tlv320aic23.c tlv320aic26.c tlv320aic32x4.c tlv320aic3x.c...
View ArticleForum Post: RE: aic3100 sound card linux driver
Im developing a new platform which includes am3352 and tlv320aic3100 codec, Im using linux-3.2.0-psp04.06.00.11. The kernel has ALSA which has tlv320aic23.c tlv320aic26.c tlv320aic32x4.c...
View ArticleForum Post: RE: TLV320AIC3100 DAC Flags & ALSA SoC Driver
Im developing a new platform which includes am3352 and tlv320aic3100 codec, Im using linux-3.2.0-psp04.06.00.11. The kernel has ALSA which has tlv320aic23.c tlv320aic26.c tlv320aic32x4.c...
View ArticleForum Post: RE: ADS12981PAG
Hi Shruthi,Go to http://www.ti.com/product/ADS1298#samplebuy. The TI e-store only handles EVMs.Best Regards,Chris
View ArticleClik here to view.
Forum Post: RE: Question regarding relative phase of multiple ADS5500...
Hi,Sorry for such a long delay on this issue. To make sure we're on the same page about what you're trying to do, let me lay out how I would go about synchronizing multiple parts. I think the key here...
View ArticleForum Post: RE: LDC1000 Inductor, 2 Inch Distance
Hello Tom,More layers will help to increase resolution for larger distances (namely, above 2-3x of PCB thickness)But this increase is insignificant.
View ArticleForum Post: RE: PCM5142 EVM GPIO Output
Hello Dave-san,I found the mistake setting.I had selected SPI Connection of EVM Communication,because customer used SPI.(Tools⇒Options⇒Target⇒EVM Communication)Then tried to select i2C Connection, the...
View ArticleForum Post: RE: LDC Software modification
The firmware on the EVM will be released by 12/20. We do not recommended modifying the firmware on the EVM unless the user programs a method for the firmware to enter BSL. Because there are no JTAG...
View ArticleForum Post: RE: ADS1298 Questions
Thank you for your help. A few more questions.2 Should WCT be tied to ground if it is not used since it is an output? Or left open?5. If the sampling rate is 2000 Hz, then the lead-off detection signal...
View ArticleForum Post: RE: LDC is like wear debris sensor
Hello,1. The tank will be driven at its resonant frequency, you cannot set it. if you want to change the frequency you need to change the sensor (cap or/and inductor)2. Correct3. No, they are...
View ArticleForum Post: TSW1400 and DAC3282
Will the TSW1400 work with both the ADC and the DAC eval cards? It wasn’t obvious to me from the documentation. The DAC3282 documentation refers to the TSW3100EVM, but I did see one note somewhere...
View ArticleForum Post: RDK Value SB
hi, i am referring to value sound bar design from TI. now my sound bar is working, except IR remote. I want to use RC-5 protocol for that. please guide me in the selection of proper IR receiver...
View ArticleForum Post: RE: TLV320AIC3106 concurrent Multiple channel capture(record)
Hi D. Hartl,Thanks for your reply.Can you please confirm it, that there is no way to record 4 audio signals (LINE 1L,LINE 1R,LINE 2L,LINE 2R) at a time separately either by TDM or any other way?Or is...
View ArticleForum Post: NEED INFORMATION-ADC128D818CIMTX/NOPB
Hi Can you please provide the following information for the ADC128D818CIMTX/NOPB Part ?1. Junction Temperature Max (Tj Max) 2. Typical Power dissipation (Pd typ)3. Maximum Power dissipation (Pd max)4....
View ArticleForum Post: RE: slau384
one more question, what is the purpose to put C91 and C94 in the circuit?thanks,David
View ArticleForum Post: RE: Spring as inductive sensor
Dear Sir, what is the mimium inductance could be measured ? Is it possible to detect inductance below 1uH to 100nH ?any specical tips in desig and implemention ?regardsHawk Tong
View Article