Forum Post: RE: Problem in SPI communication with ADS1148 EVM
Hello Mr.BOB. Thank you for your support. It has been really helpful in implementing our circuit faster for our prototype. As per your recommendations I have made the necessary changes in the overall...
View ArticleForum Post: DAC5689 problem
Hi allThere is a question by setup of DAC5689.Table 5. Register name: CONFIG3 Address: 0x03, Default 0x00Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 diffclk_dly(1:0) clko_dly(1:0) Reserved...
View ArticleForum Post: RE: WEBENCH and PCB Coil
Hi Valentin,we tried to do it same way, but the import of Autocad-spiral dxf in Altium does not work properly. How did you do it? Any hints / ideas? We have a 4-layer 7.7mm 14 turns spiral, width...
View ArticleForum Post: Inductive Sensing
Could you please give me some idea as to what platform can we use to interface the LDC1000 chip with other circuits components like capacitors and inductors?? it wont be possible to make connections...
View ArticleForum Post: Four questions about ADS1298 for EEG
Hello.In the case of setting Vref from external electric source,how much is Vref setting range?Vref means voltage between VrerP and VrefN.Writing Input-Referred Noise:4uVpp on features of ADS1298...
View ArticleForum Post: RE: High Speed Data Converter Pro v2.2 stopped working
Is there any solution? We can't start our project bacause of this problem.
View ArticleForum Post: LVDS(FlatLink) to CSI-2 or 8bit+SYNC
Welcome everybody. It's my first post here.I'm about to to connect my Sony FCB-SE600 to Tegra 3 module.Sony output: 1 x CLK + 4 x Data differential lanes, Y/Pb/Pr 4:2:2 (LVDS) (y:8bit, C: 8bit, Vsync,...
View ArticleClik here to view.
Forum Post: DAC3482EVM
Hello,I have a bit stream of 1s and 0s. And I am making a digital signal out of it. If it is one I have some amplitude which is positive and if it is 0, I have a negative amplitude. Basically half of...
View ArticleForum Post: RE: TSW1400 and DAC3282
Dan,The TSW1400 does work for both CMOS/LVDS ADC and DACs. The DAC3282 is working with the TSW1400.If you want to connect both an ADC and a DAC to the TSW1400 at the same time you can use this TI...
View ArticleForum Post: RE: TLV320AIC3106 concurrent Multiple channel capture(record)
Not with the AIC3106 because it has only 2 ADCs. You will need to use either two AIC3106s or a codec with four ADCs, like the AIC34.
View ArticleForum Post: RE: High Speed Data Converter Pro v2.2 stopped working
Hi,Did you try uninstalling and reinstalling? Please try this if you haven't.I have a feeling that this has to do with the USB chip drivers. Can you try to open HSDCPro after unplugging all USB devices...
View ArticleForum Post: RE: Power Consumption / Better recommendation of TLV320xxx
Hi everybody,We would like power consumption value for TLV320AIC3263. Can't find them on the datasheet for some reason... Nor the application reference guide. Is it the most low power part of our...
View ArticleForum Post: RE: TIPD120 accuracy
Hello Suresha,Many systems specify accuracy/error in terms of %FSR which means the accuracy in percent of the full-scale range. We are going to update some things about TIPD120 and one of them is to...
View ArticleForum Post: RE: ADS8528: Issue Writing to the Configuration Register
Hello,I wasn't able to get the INT signal to work, so I decided to use the negative edge of the busy signal, which works.The problem I am having now is that some of the data read from the ADC doesn't...
View ArticleForum Post: RE: Source code DSP TMS230 for the MMB0 with ADS1299 EEG FE
You should receive an email shortly with the requested information
View ArticleForum Post: RE: Spring as inductive sensor
Hello Christophe,As a side question - did you manage to make this spring to oscillate at all? I would think it's not possible, but again, I do not know the material and wire diameter...
View ArticleForum Post: RE: ADS8504 internal voltage reference
Hello Tom,I forgot to clarify that the operational temperature range of -40°C to +85°C is ambient temperature for both the ADS7804 and ADS8504. Also, sorry about the “investing” typo in my previous...
View ArticleForum Post: RE: Problem in SPI communication with ADS1148 EVM
Hello Mr.BOB. Thank you again for your support. As per your recommendations I have made the necessary changes. Again I am sending my 32 channel scheme (Please visit the site to view this file)after...
View ArticleForum Post: RE: Lowest Vref for DAC 8564
One addtional Informationit is +/-150 mVThanks & RegardsAravind
View Article