Forum Post: RE: DAC539G2-Q1: SMART-DAC-EVM-GUI Error in VI at startup in...
Hello Katlynne Thank You for the reply. The device shows up as two Interfaces A and B The driver installed is 2.12.36.4 on all systems that I could check on windows 10 and 11 ( all Intel processor...
View ArticleForum Post: RE: AMC3336: AMC3336 DC-offset problem
Dear Alexander, Even if I keep CLK low during power up it did not help. Sometimes the first clock from Diif.line.driver SN65C1167E seems not to keep duty cycle 50%/50% but starts at 38%/62% duty cycle...
View ArticleForum Post: RE: AFE58JD18: AFE's with DC coupled LNA input?
Hi Sachin, My application is a multi-channels data acquisition FMC board, and I need a bandwidth from DC to 30 MHz. The ADC's specifications are given above. Some of your AFE's would be perfect,...
View ArticleForum Post: RE: ADC12DL3200EVM: ADC Control Package Read Register Issues
Hi Hunter, I'm going to take this offline and onto an email thread to loop in others. Please be on the lookout for that. Thanks, Chase
View ArticleForum Post: RE: ADC09QJ1300: Full Scale Range Adjust FS_RANGE does not work
Joseph, This is implied as each register address space address is only 8 bits. I'll bring this to the attention of the people that do the datasheets. Regards, Geoff
View ArticleForum Post: RE: ADS127L11: Output data problem
Hello Keith, Thank you for your reply. I have checked voltage@ pin4 3V5 DC and pin 5 2V5 DC, I was using DMM, also board GND is connected to GND of the power supply. Still getting similar plot, please...
View ArticleForum Post: RE: ADC3562: Regarding overvoltage protection for Analog Input...
Hi Oda, Please use the abs max ratings on the analog inputs. At no time, should the input signal, with either an amplifier or balun coupled to the inputs, should be not exceed the analog input abs max...
View ArticleForum Post: RE: ADC3422: test PRBS generated on LVDS outputs
Hi Andrea, I will need to discuss with design on those specifics. Please give me a few days to respond back. Thanks, Rob
View ArticleForum Post: RE: ADS1148: Compliance voltage of IDAC Pin
Hi peimin Wu, I tried to make it a little more clear on the plot below As you can see, at 500mV of compliance voltage the normalized current is closer to 0.92 for 250uA and 100uA (I am not sure where...
View ArticleForum Post: RE: ADS1261: Responding with All Zeros
You are correct, I noticed the same thing myself this morning, somehow our logic analyzer channels got changed. This should be fixed now in the following diagram. In the same order the channels are...
View ArticleForum Post: RE: ADS1120: Microcontroller to pair with ADC
Hi Drake Burtum, [quote userid="648206" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1493700/ads1120-microcontroller-to-pair-with-adc"]I'm looking for a microcontroller...
View ArticleForum Post: ADS131E08: Vcm ADS131
Part Number: ADS131E08 Tool/software: According with thin scrrenshot, if INxN=0 INxP min should be betwen AVDD-0,3-INxPmax/2 and AVSS+0.3+INxPmax/2 So I can't use the most of the range beacuse in low...
View ArticleForum Post: RE: ADS1220: Only returning 0xFFFFFFFFFF after sending RDATA command
Hello Bryan, It is still doing strange! I've removed all filters and the Rref. I connected a power supply AIN0 and AIN1 inputs. All registers are on default. I first send a START/SYNC command followed...
View ArticleForum Post: ADS1292R: Chip does not react
Part Number: ADS1292R Other Parts Discussed in Thread: CC2340R5 , Tool/software: Hello, I am working on an ECG project which implements the ADS1292R in combination with the CC2340R5. The ADS1292R does...
View ArticleForum Post: AMC6V704: detailed documentation needed
Part Number: AMC6V704 Tool/software: My company, Advantest is planning to use this part in our design. I need more detailed documentation (register address map, SPI protocol information, etc.) in...
View ArticleForum Post: RE: ADS1261: Responding with All Zeros
Hi Everett Everett, Your SCLK is still triggering on the wrong edge in the capture (should be on the falling edge). If that is the case for just the analyzer, then that shouldn't affect the...
View ArticleForum Post: RE: VSP5324-Q1: technical assistance request (Q1088C0)
Jun, Thanks for reaching out! Unfortunately, we don't have any development or evaluation boards for this part. Regards, Shane
View ArticleForum Post: RE: AMC6V704: detailed documentation needed
Hi Alan, Please request via this link: https://www.ti.com/drr/opn/AMC6V704-DESIGN Best, Katlynne Jones
View Article