Forum Post: ADS131M08: START / STOP conversion of ADS131M08
Part Number: ADS131M08 Tool/software: Hi , For the ADS131M08, can you please inform where to find commands to stop conversion, and restart conversion in the datasheet ? On page 42 , the commands are...
View ArticleForum Post: RE: ADS1298ECGFE-PDK: Getting Spikes in Between Data which...
Hi Ryan, When we use RDATAC and short the input to ground the we are able to get a straight line centred to zero with noise. But when we do same with RDATA we get shifted data. and here are Answers of...
View ArticleForum Post: RE: ADS131M08: START / STOP conversion of ADS131M08
Hi Saad, the ADS131M08 does not offer dedicated "Start or Stop conversion" commands. You stop conversions by sending the "STANDBY" command, and then start conversions by sending the "WAKEUP" command....
View ArticleForum Post: RE: ADS131M08: START / STOP conversion of ADS131M08
Hi Johachim, what are the commands 0x11 and 0x08 which I see people using to stop and start conversion. I was looking for these commands in the datasheet without success ! Also , how do can you write...
View ArticleForum Post: ADC08DJ5200RFEVM: How to set the sampling frequency without using...
Part Number: ADC08DJ5200RFEVM Tool/software: I can set the clock and parameters on the board via this GUI from TI. But I want to know if I can write to the register of the clock chip and the adc chip...
View ArticleForum Post: RE: ADS131M08: START / STOP conversion of ADS131M08
Hi Saad, the ADS131M08 doesn't offer those commands. Other TI ADCs offer such commands, but not the ADS131M08. We recommend to only write registers to change the device configuration when you are in...
View ArticleForum Post: RE: DAC80004EVM: controlling DAC8004 EVM using esp8266 nodemcu
Hello , i want to send a shown below command 4th in the table below ,very important clock and data relations. Is it ok? 00000011 00001111 11111111 11110000 FULL transmition: PARTIAL
View ArticleForum Post: RE: ADC12DJ3200: adc12dj3200
Hi, Please let us know if you are using the ADC12DJ3200EVM from TI or your own board design. Please send over all the register writes that you are configuring the ADC with in JMode0. This will allow...
View ArticleForum Post: RE: ADC10D1500: HD2,HD3 graph for the band 600MHz to 2GHz
Hi Sarojini, We are trying to solve this, we have another option to try this coming week. I will keep you posted on how this turns out in collecting the data. Regards, Rob
View ArticleForum Post: RE: ADC08DJ5200RFEVM: How to set the sampling frequency without...
Hi Bowei, Yes it is possible to control the ADC board through USB you will have to interact with the FTDI chip on the board itself to control the SPI writes. Yes, installing the jumper J19 will switch...
View ArticleForum Post: RE: ADC08DJ5200RFEVM: How to set the sampling frequency without...
I didn't want to write to ADC because I don't need to. I actually want to interact with the clock chip so I can set the sampling rate. Also, can you please teach me how to control the ADC and clocking...
View ArticleForum Post: RE: ADC081C027: I2C ADC with many addresses
Thanks Joel, I think TLA2528 might be the best option for now. Sorry about the delayed response. Additional application info: I think a point of load offering would be incredibly valuable. Similar to...
View ArticleForum Post: DAC39RF10-SP: output 3dB degradation
Part Number: DAC39RF10-SP Tool/software: Hi, There is issue 3dB lower output power than expectation. Please check below questions. 1. Can it increase output power level with increasing switched output...
View ArticleForum Post: RE: ADS8355: Reference code for ADS8355
do you have sample code for ADS8353
View ArticleForum Post: RE: ADS1299: Measure using BIAS
Hi Ryand, Thank you for your patience. When I use WhaleTeq SEEG100 to generate sin waveform. The ADS1299 doesn't measure correct value in BIAS measurement. ( Note: When I configure ADS1299 as NON-BIAS...
View ArticleForum Post: RE: AMC130M02: Method for converting single end into differential...
Hi Saleh, My question was not good. I am sorry. Since the signal input to AMC130M02 is single-ended, I asked how to convert the single-ended signal to differential. The application note describes how...
View ArticleForum Post: RE: AFE781H1: UART Break communication is not reliable
Hello Joseph, I apologize for the delay in getting back to you. The issue was on the MCU clock timing side. After changing the MCU clock time, DAC responded to all the queries. Thanks for your...
View ArticleForum Post: RE: AFE4960PEVM: Dual AFE
Hi Ryan, Thanks for your reply. I tried updating the firmware as you said and I'm getting the same Reset property not found error. But I'm getting wave now. I have attached the ECG waves for your...
View Article