Forum Post: RE: ADS4145: Register read value : address 4Ah
Hi, As I replied 18 days ago. There may be a different board available than the one I'm checking. I'll check that out. Please give me some time. Regards,
View ArticleForum Post: LM27313: Marking
Part Number: LM27313 Tool/software: Hello! Several suppliers offer to buy microcircuits with this marking. The markings have crooked symbols. Is this the original marking? Thank you! Best regards,...
View ArticleForum Post: RE: ADS131M08: How are the metrology-fir-table.c generated in...
Hello Chu, Author says to modify and build the attached "generate-phase-shift-table.c" using cygwin. Example -> g++ -o run generate-phase-shift-table.c It creates a file run.exe. To create the new...
View ArticleForum Post: RE: ADS1255: ADS1255 Output voltage Calcualtion
Hi ALbert Tello, Please review the datasheet for this type of information: -Bryan
View ArticleForum Post: RE: ADS131M08: continuous data reading
Hi Felipe de Andrade, I tried recreating your code, see below. I am sending the exact settings you have that write to REG 0x03 to turn off all channels except ch0 I applied -0.5V to ch0, and you can...
View ArticleForum Post: RE: LMP92066: Voltage regulator to source -5v
Hi Vaishak, It looks good to me. These might not show on the snippets, but make sure there's a small (~10nF) capacitor on the FETDRV outputs. Also note, your GaN sheet doesn't show pullups on the I2C...
View ArticleForum Post: RE: ADC122S021: Replacing MCP3202T-BI
Hi Conor, I would expect the ADC122S021 to still be able to support a 5.5V supply, but I understand the operating conditions only specify up to 5.25V. In that case, the ADS7230 seems to fulfill all...
View ArticleForum Post: RE: DAC7573: power on reset
Hi Yumoto-san, The POR circuit is based on the VDD supply. Turning off IOVDD will not reset the device or the I2C block. Best, Katlynne Jones
View ArticleForum Post: RE: ADC3683EVM: Access to 20-bit mode GUI selection and bit...
Hi Maxim, 1)No, there is not another program or option. 2/3)Outside of developing python code to send and read SPI signals over the FTDI chip, the best way to program this use case is to load a .txt...
View ArticleForum Post: RE: ADC3683: SPI write utility
Hi Maxim, I answered your question in your other related E2E post. Therefor I will be closing this one. Relevant post: (1) ADC3683EVM: Access to 20-bit mode GUI selection and bit deserialization using...
View ArticleForum Post: RE: AFE4960PEVM: Dual AFE
Hello Iasikha, Within the installation directory, there should be a folder with the EVM Firmware (C:\Program Files\Texas Instruments\Bio-Sensing\AFE4960PEVM\EVM Firmware) You will find a file called...
View ArticleForum Post: RE: DAC38RF80EVM: Recommendation for a Cost-Effective Xilinx FPGA...
Hi Vandana, This will be difficult to answer, because the FPGA selection should first be made based on number of SERDES Lanes needed, and the speed capability of the transceivers. This alone can mean...
View ArticleForum Post: RE: AFE4410: sample code for customer reference
Hi David, Thank you for supporting our AFE4410. Please send an email to the mailing list due to the confidential nature of this device. biosensing_afe-support@list.ti.com Thanks and regards, Ryan
View ArticleForum Post: RE: ADS1213: Checking support on ADS1213E part
Hi Suresh G, We will look into this and get back to you in the next few days, thanks for your patience -Bryan
View ArticleForum Post: RE: ADS1282: Calibration sequence clarification and SDATAC questions
Hello Vincent, My apologies for not getting back earlier. At this point, I assume you were able to verify the above sequence. Yes, the above procedure is correct and should work well in your system. I...
View ArticleForum Post: ADC12DJ3200: adc12dj3200
Part Number: ADC12DJ3200 Tool/software: Hi! I have a problem when using adc12dj3200. The ADC is set to JMODE 0, but DA1 in the A link is corrupted. I tried using the JEXTRA_A register mentioned on...
View ArticleForum Post: DDC112: count is not stable
Part Number: DDC112 Tool/software: We have use DD112U (Dual Current Input 20-Bit ANALOG-TO-DIGITAL CONVERTER) use in out instrument but same issue observed. 1) Selected Range 0 (count is 1000) but...
View ArticleForum Post: DAC3482: VCO frequency range
Part Number: DAC3482 Tool/software: Hello, My customer would like to use DAC3482 with the following conditions. DACCLK=107.52MHz fDAC=107.52 x4 = 430.08MHz Prescaler = /8 VCO frequency = 3440.64MHz....
View ArticleForum Post: DDC112: share minimum range
Part Number: DDC112 Tool/software: share minimum and type range of Range 0
View ArticleForum Post: DDC112: FAA number
Part Number: DDC112 Tool/software: Dear Texas Team, Please share FAA engg number.( India (Mumbai engg)
View Article