Forum Post: TLA2024: How does TLA2024 guarantee the linearity ?
Part Number: TLA2024 Hi I would like to know answer about thread title. "How does TLA2024 guarantee the linearity ?" Thanks.
View ArticleForum Post: DAC38RF85: PLL_VCO field in PLL_CONFIG2 register - VCO tuning
Part Number: DAC38RF85 Section 8.4.3 of the datasheet provides a description of how to set the PLL_VCO field in the PLL_CONFIG2 register to tune the VCO frequency. It makes no mention of temperature or...
View ArticleForum Post: RE: DAC3171: The noise base of DAC3171 monotone signal is much...
Dear Neeraj: Customer tested their board found the below 2 issues, and want to know the below issues whether is the root can not configure the DAC in 7 BIT interface mode. Pls. kindly help to give some...
View ArticleForum Post: RE: ADS54J42EVM: JESD204B Interface between ADC & Intel Arria 10...
Hi Neeraj, Thanks for the reply. I've been working on this over the week and I think I've solved it. I was given modified (corrected?) configuration files by an engineer at the TI local distributor in...
View ArticleForum Post: RE: AMC1210: Modulator Failure Interrupt Not Working
Hi Alex, Sorry for the long delay. I won't be able to provide a schematic, however I can let you know that the signal on the CLK line of the AMC1210 is supplied by a 32 MHz clock oscillator chip. The...
View ArticleForum Post: RE: ADS1278EVM-PDK: Need Labview GUI source code for ADCPro for...
Hello, Thanks for your response. Unfortunately the source code provided either requires a password to see the source code, or the Labview VIs lack the diagram so we are unable to open them in Labview...
View ArticleForum Post: RE: DAC38RF82EVM: Register settings required for the 81180 for...
Hi Jim, Thanks for the support, we were able to resolve the issue. we were able to interface dac38rf82evm to kcu105/VC707 board and generate the frequencies we wanted. The performance of the DAC over...
View ArticleForum Post: RE: AMC1305M25: do we have Verilog source code for Sinc filter
Hi Yuan, Take a look at the reference design for the ADS1202 . We have a VHDL code example there that does the SINCx filtering, it would be the same for the AMC1305.
View ArticleForum Post: RE: ADS1298: Data converters forum
Hi Alexander Smith Thanks for replying. Problems were sorted out , Actually the problem was due to conversion from hex to decimal. With your assurance on register settings we had another look on the...
View ArticleForum Post: RE: DAC7811EVM: IAM NOT ABLE GET accurete voltage corresponding...
hello.. i can't understand reserve command and NOP command .what i make actually in my design VHDL code i make 16-bit data i sent 1 and i am getting 1 in MOSI that MOSI i connected to spi pin in...
View ArticleForum Post: RE: AMC1305M25: do we have Verilog source code for Sinc filter
Hi Tom, Thank you! \^o^/ Yuan
View ArticleForum Post: RE: ADS1209: Gain error and reference voltage.
Hi Tom Thank you for your answer. I just wonder, if the Gain Error parameters include the errors of the internal reference why are the errors of the reference then much bigger than the Gain Errors...
View ArticleForum Post: RE: VSP5610: VSP5610 AApplication circuit diagram
Hi Sheree, I have sent you an email. Please check it for the application circuit diagram.
View ArticleForum Post: RE: ADS7142: How to set continuous sampling to 140-ksps
But use the manual mode to configure continuous sampling，Need to provide continuous SCL signal, this unless hardware add SCL clock chip？ I've tried using software that doesn't seem to work？ so let's...
View ArticleForum Post: DAC7811EVM: the DAC7811 EVm is not taking the data from master...
Part Number: DAC7811EVM hiii.... when i supply correct MOSI and SCLK and CS for J2_B with pin numbers MOSI as J2B_11 and SCLK as J2B_3 and CS as J2B_7 and Vref and VDD . the DAC7811 is not considering...
View ArticleForum Post: DAC80004: DAC80004IPW query & CLR pin
Part Number: DAC80004 Hi, In my design with DAC80004IPW, the CLR pin is left floating. I don't see the DAC output changes with reference to the programmed DAC input code. The LDAC pin is tied to ground...
View ArticleForum Post: ADC128S052: ADC128S052 result bit?
Part Number: ADC128S052 In ADC128S052 test, we found that the ADC result was 11 bits, and the datesheet did write 12 bits. Is it correct?
View ArticleForum Post: RE: ADS131A04: Internal reference outside spec (2.442V +/- 0.1%)
Joseph, As you can read from previous messages, we have now found 15 ADCs with a value outside the spec 2.442V +/- 0.1%. From a total number of around 800 ADC. We do not have a table with reference...
View ArticleForum Post: RE: LMP92066: About thermal pad
Hello, I have never known any mechanical package details to include height of the thermal pad in the description. Generally speaking it is flush, or nearly flush, with the package itself. Why is this...
View ArticleForum Post: RE: ADC32RF45EVM: what is the input voltage range of a...
Hi Chi, You can connect LVDS SYNCB signal directly to 1.8V bank. It should work. ZCU102 is compatible with ADC32RF45EVM directly. Regards, Vijay
View Article