Forum Post: RE: ADS8363: 18-bit resolution for ADC product
Can you confirm if you need 1MSPS from all 4 channels in parallel or if you need a 1MSPS sampling rate divided by the four channels? ADS8594 has 4ADCs in parallel @ 500kSPS ADS8694 has 4ADCs MUX'ed @...
View ArticleForum Post: RE: RTOS/ADS1298: Lead off AC Mode Behavior
Hello Jameel, Thank you for your post! We will need to see a connection diagram showing where the 30k resistor is connected in your circuit. Can you please provide a schematic and the complete list of...
View ArticleForum Post: RE: ADS1262: ADS1262: ADS1262 Load Cell Schematic Review (continued)
Hi spanky, An output code of "250000" is much more reason that what you'd be observing before... For a gain of 1 V/V and a 5V reference, "250000" corresponds to a voltage measurement of 0.58mV, which...
View ArticleForum Post: RE: ADC128S102EVM: ADS128S102
Hi Vichu, Welcome to TI's e2e Community. There are no internal calibration registers in the ADC128S102 , I do not think the EVM is calibrated. The output codes in decimal are converted to voltage with...
View ArticleForum Post: RE: ADS1675REF: Windows 10 Driver for the TI Analog-to-Digital...
Hi Tom, As I stated previously, I have Chris Seberino in the Houston, Texas area developing the driver we need in order to have our signal analyzer software, DynamicPRO, be able to request digitized...
View ArticleForum Post: RE: DAC38RF82EVM: Register settings required for the 81180 for...
Rajesh, Sorry for not getting back sooner. Please do the following changes to your procedure: 1. Change K =19 on JESD block page. This is what the FPGA will be set to. 2. Leave N and N' as 15. 3. On...
View ArticleForum Post: RE: ADS7886: max current through IN-to-Vdd diode
Hi KF, The ESD diodes are present and when the current is specified, the max continuous current rating is usually between 5-10mA. 0.5mA will be fine. Please note that we cannot guarantee proper...
View ArticleForum Post: ADC Input Type Question and Part Recommendation
Hello, I'm trying to select an ADC right now and I'm a bit confused by all the different ADC input types and which is the right one for me. The signal that I'm converting is coming from the LA 55-P...
View ArticleForum Post: RE: ADS54J69: Filter mode
Hi Jim, Any feedback from the design team? Thanks! Patrice
View ArticleForum Post: RE: ADS114S08EVM: Download Problem for ADS114S08-dvcpkg.exe
Hi Stanley, I already downloaded before I responded the last time. I'm not sure what to tell you. What browser are you using? You could try to delete your history/cookies to see if that helps. Could...
View ArticleForum Post: RE: DAC38RF80: What to do with CLKTX+- (Pin no.-A7 and A6) when...
Hi Eben, Any update on the single ended mode operation of CLKTX+- pins of DAC38RF80 ? Thanks, Lalit
View ArticleForum Post: RE: DAC38RF80: JTAG connection
Hi TI, Please respond to this. Its urgent for us. Thanks, Lalit
View ArticleForum Post: RE: Need advice for ADC. Best option for ±20mA &±10V input ranges...
Hi Matias, Take a look at the ADS8688 , with that part you wouldn't need a MUX and you would have plenty of headroom on the sampling rate..
View ArticleForum Post: DAC084S085: OFFLINE REQUEST
Part Number: DAC084S085 Dear Sir: I'll send you a question, DAC084S085 startup sequence. When system start DIN and SCLK port voltage of DAC084S085 was midpoint potential voltage. DAC084S085 was...
View ArticleForum Post: AMC1305M25: do we have Verilog source code for Sinc filter
Part Number: AMC1305M25 Hi, For customers using AMC1305 and FPGA, do we have Verilog codes for Sinc filter? Thank you! Yuan
View ArticleForum Post: AFE4404EVM: Inductor on the input
Part Number: AFE4404EVM Dear TI 1. Why the EVM put an indutor(L1) on the analog input? Will it not affect the frequency response? 2. The protection diodes(D3~D7) are for ESD or the feedback current of...
View ArticleForum Post: ADS1015-Q1: ADS1015 configuration
Part Number: ADS1015-Q1 Hello We try to configure the ADC in the following way : At init we enable alert/ready interrupt by setting Hi_thresh register MSB to 1 and Lo_thresh register MSB to 0. We write...
View ArticleForum Post: LMP92066: About thermal pad
Part Number: LMP92066 Hello support team, I have a question regarding thermal pad of LMP92066 . Our customer wants to know the height value of the thermal pad . On page 62 of the datasheet, there is a...
View ArticleForum Post: ADS1298R: Respiratory circuit Hardware design
Part Number: ADS1298R Hello, While designing the hardware for my custom board using the ADS1298R , I was looking at integrating the respiratory signal. Since the ADS1298R generates respiratory signals...
View ArticleForum Post: ADS1243-HT: SNR & THD parameter
Part Number: ADS1243-HT Hello TI Team, What are the SNR and THD parameters of ADS1243 ?These two parameters were not found in ADS1243-HT datasheet.Customers need these two parameters. Could you share...
View Article