Forum Post: Di washability for converters, inverters,memory, regulators,...
I want Di washability of converters, memory, regulators, transreceivers, OP-amp, timers, digital logic gates, inverters,controllers, RFID base station, etc. for Ti SMD parts
View ArticleForum Post: DAC38RF83: SYSREF+/-, DACCLK+/-
Part Number: DAC38RF83 Hi I want to connect the LMK04616 to SYSREF+/-, DACCLK+/- inputs. The LMK04616 outputs are 8mA HDSD, 4mA HDSD and 16mA HCSL. Which of the option I need to use and what kind...
View ArticleForum Post: ADS1218: Infrequent wild data outputs are received from the...
Part Number: ADS1218 We have been using the ADS 1218 for for several years for pressure and temperature sensor data acquisition and produced few hundreds of card(with 48 ADC on board) working...
View ArticleForum Post: DAC7811EVM: IAM NOT ABLE GET ANY VOLTAGE AT TP2
Part Number: DAC7811EVM Hiii...... this is my clk and cs and mosi that iam getting from fpga board i conected this three with DAC7811 WITH J2_B ASS MOSI WITH J2_B11 AND CLK WITH J2B_3 AND CS WITH J2B_7...
View ArticleForum Post: RTOS/ADS1298: Lead off AC Mode Behavior
Part Number: ADS1298 Tool/software: TI-RTOS Hi, We are using the ADS1298 lead off detection, using AC mode. we did this by writing to the lead off control register value 0xE1 and value 0xFF for both...
View ArticleForum Post: TSW14J56EVM: linux API and firmware
Part Number: TSW14J56EVM Hi all, We would like to run our TSW14J56EVM board under linux, and were wondering, whether, first, there is an API for communicating with the device. (We are interfacing with...
View ArticleForum Post: ADS8363: 18-bit resolution for ADC product
Part Number: ADS8363 Hi there: We'd like to find an solution with 18-bit SAR ADC (4XADC), 1MSPS criteria. The most closest us ADS8363 , but it only has 16-bit. Do we have 18-bit one? or other suggestion?
View ArticleForum Post: ADS1209: Gain error and reference voltage.
Part Number: ADS1209 Hi When looking at the datasheet for the ADS1209 i am in doubt how to understand the Gain error and the Gain error thermal drift parameters (GÂ ERR and TCG ERR ). For the gain...
View ArticleForum Post: VSP5610: VSP5610 AApplication circuit diagram
Part Number: VSP5610 HI, I need to interface VSP5610 with CCD sensor, so I need Application circuit diagram for the same.
View ArticleForum Post: DAC38RF85: Device start-up time
Part Number: DAC38RF85 Is there any data available regarding the startup time for this device ? How long after device reset before the SPI interface is usable ? How long after device reset before the...
View ArticleForum Post: ADS124S08EVM: Output data analysis from strain gauge interfaced...
Part Number: ADS124S08EVM Hello sir, Actually I have done SPI interfacing with skin friction sensor as a input using EVM ADC and arduino UNO. When I am loading the skin friction sometimes the data will...
View ArticleForum Post: ADS131A04: Conversion Latency
Part Number: ADS131A04 Hi Sir I saw ADS1261 have conversion latency table May I know how to calculate conversion latency time of ADS131A04 ?
View ArticleForum Post: DAC8775: power dissipation
Part Number: DAC8775 Hi Sir I saw DAC8775 have adaptive power control and have better power dissipation May I know what's the impact caused by power dissipation ? for example thermal will effect DAC...
View ArticleForum Post: RE: ADS1218: Infrequent wild data outputs are received from the...
Hi Haresh, This sounds like a random failure. Was this a field failure? Or a failure in your normal test flow? We can possibly narrow down the issue. How are you reading the data? Are you using the...
View ArticleForum Post: RE: ADS1263: Data corrupted with external reference
Hi Fernando, I'm sorry for the delayed response. The STATUS bytes you're showing (72 with good data, and 73 with bad data), indicate two different errors: STATUS = 72 = 0x48 ( ADC1 data new &...
View ArticleForum Post: RE: ADS131A04: Conversion Latency
Kai, You're referring to the Conversion Latency table shown in the ADS1261 datasheet on page 44. For the ADS131A04 , we don't have such a table. However with the sinc3 digital filter, the latency for...
View ArticleForum Post: RE: ADS124S08EVM: Output data analysis from strain gauge...
Hi Sushmita, Your program loop only lasts a few milliseconds, so I'm not sure what you expect to see. Also, the output of the ADS124S08 is binary 2's complement so you need to properly sign-extend the...
View ArticleForum Post: RE: ADS8168EVM-PDK: Evaluating the pseudo-differential mode
Hi Friedrich, We are working on cleaning the register files up. We should have an update on the web no later than next Monday. I will reply back to this e2e thread once we have these released. Thanks!...
View ArticleForum Post: RE: ADS1247: Protection of inputs against IEC60255-27/IEC60950-1...
Hi Mikael, Thank you - it looks great. The main concern I have here is the inductor on pin 14, AVDD. There should not be any inductance on the power supply for this device family. I would expect that...
View ArticleForum Post: RE: ADS1298: How to properly use the RLD functionality
Hi Spencer, 1. The RLD electrode is an output. 2. Correct. 3. The signal still needs to come out of RLD_OUT so that the RC filter can set the phase of the signal. You can either connect the...
View Article