Forum Post: RE: ADS130E08 Sample Code
There is a potential conflict if the MMB0 motherboard outputs are in conflict with the Arduino micro. You would want to make sure this is not the case.
View ArticleForum Post: RE: ADS131E08 Data read
Using a timer is an option, but risky. Timer aren't exact for this kind of timing and you may over time get out of sync and lose samples. But this is your design decision.DOUT is updated and be...
View ArticleForum Post: RE: RE:Connecting Thermocouples to the ADS1148
HI Dhiren,You can use the BCS to check if the TC is open, just don't leave it on when you take a temperature measurement as this will add error. In other words, take two separate measurements.As far...
View ArticleForum Post: RE: TSW1400evm firmware download intermittent problem
SM Do you get the message below after you have selected a device and start the firmware download? Does the message appear right away or is there a delay, which might indicate the firmware is...
View ArticleForum Post: RE: Formula for LDC1000 resonant frequency and frequency counter...
Hi Sunny,Regarding the filter cap, I had already adjusted it so that the CFB voltage is 1V p-p, as advised in the literature. Let me be clear: My numbers are with 1V p-p on CFB, my frequency is...
View ArticleForum Post: RE: ADC1247 3-wire 10k type-2 RTD setup
Hi Mirzo,Welcome to the forum! I'm a little confused as to what you are actually connecting. Is it an RTD or a thermistor? Based on the post heading and the value you have chosen for R12, it appears...
View ArticleForum Post: RE: ads1299 and msp code?
Dear Ryan,send me too please. ist.abdulqadir@gmail.comRegards,AK.
View ArticleForum Post: RE: TI high speed equipment
Hi Airat,You should be able to view the output of AFE7225 on either SMA J5 (or IOUTA) or SMA J7 (or IOUTB) for channels 1 and 2 of the DAC respectively.Please refer to section 2 of the document below...
View ArticleForum Post: DAC161P997 HART Injection signaling...
The grounds on this chip are very particular and the information for injecting the FSK HART signal are very sparse. The HART subsystem in our meter draws about 30mA so it is impossible to make it loop...
View ArticleForum Post: RE: DAC3174
Yes, you can do that. You still have to live within the output compliance voltage range, so doubling the current means you can drive a lower impedance - not get larger signal amplitude.Regards,Richard P.
View ArticleForum Post: RE: ADS1298R - Respiratory and EKG simultaneously
Hi Eric, Yes - respiration and EKG can be measured at the same time using independent channels (RESP - CH1, EKG - CH2-8).The reality is that the 32kHz modulation signal injected onto the leads also...
View ArticleForum Post: RE: PCM5141/PCM5142 Power Dissipation
Hi Don-san,Do you have any updates for this issue?Best Regards,Kato
View ArticleClik here to view.
Forum Post: RE: LDC1000 application questions
Hello Viktorija,"Does the LDC1000 EVM board allow for external sensors to be created and used without having to lay out new hardware on the board?"Yes it does. You can snap the coil portion of the...
View ArticleForum Post: RE: Why is the default value of Rp_MIN listed as 0x14? (LDC1000)
Great, I am glad I could help.
View ArticleForum Post: ADS1258 channel indexing problem in auto-scan mode
I am using the ADS1258 in auto scan mode and channel data read command mode.I can write to and read from registers successfully (MUL =0)I do not use DRDY but I have START tied high to always convert...
View ArticleForum Post: RE: resolution and L inf uH
Hello Florent,"what is the resolution of the coil default on the evaluation kit. I want to make an angular measurement. How do I know that when the metal surface that covers it no longer does change...
View ArticleForum Post: RE: Can't install LDC1000EVM driver, using macbook and fusion 6...
Hello Anton,I agree, the issue that you are seeing doesn't appear to be related to your VM.The GUI automatically installs the necessary drivers. It should not be necessary to install drivers through...
View ArticleForum Post: RE: PCM5102A Current Driving Capability of VNEG Terminal(-3.3V)
Hi, Kato-San,This is not allowed. Sorry. D2
View ArticleForum Post: RE: TLV320AIC3254 coded interfacing to OMAP4460(Jorjin module)
Hi, Raghu,Unfortunately, we do not provide driver support. Maybe someone in the Community can check your log and comment. D2
View ArticleForum Post: Footprints for ads7953
Our college has purchased 20 ads7953 but i am not getting the eagle footprints for DBT-38 (TSSOP 38).So, how to get the eagle footprints for TSSOP 38 ??
View Article