Forum Post: RE: ADS130E08 Sample Code
The schematic of the EVM is included in the user guide for reference. You can see how all the signals are connected from the analog, digital, and power headers. 5V and 3.3 and/or 1.8V are needed for...
View ArticleForum Post: RE: RE: ADS1232 Reference Voltage and Gain
Hi Joseph,I split your question from the previous post as your question is on a different topic. Also, the previous post was very old.With a 0.9mV/V load cell and 5V excitation your maximum deflection...
View ArticleClik here to view.
Forum Post: RE: Power-Up Sequence of ADS1298
Hello Michael,This section of the datasheet is intended to ensure that the device is properly initialized, both analog and digital portions. Upon manufacture, One-Time Programmable (OTP) registers are...
View ArticleForum Post: RE: DAC3484evm
Safal,The default EVM user's guide provide instructions assuming your have an external clock to the J9 connector. If you do not have an external clock, you may load the following files from the DAC348x...
View ArticleForum Post: RE: SLAA541
Thanks for the swift response!Having struggled with this for a day I actualy managed to progress to the next issue, so I might have been a bit quick on the trigger posting here.I don't use a master...
View ArticleForum Post: RE: ads 1258 auto scan missing a few channels occassionary
Hi Woon,You should check your power supply connections and make sure that the oscillator is functioning properly.Best regards,Bob B
View ArticleForum Post: RE: Not able to receive the same conf bits (ADS1118)
Hi Shravan,According to the scope shots and the configuration you are writing, the data agrees. So you are reading back what you are writing. What you may see as a difference is bit 15 of the...
View ArticleForum Post: RE: LDC1000 EVM GUI 1_0_4_1
Vittorio,Please downgrade the firmware and GUI until the issues have been resolved. I apologize about the inconvenience. Please follow this procedure for downgrading the firmware:uninstall GUI 1.030...
View ArticleForum Post: RE: LDC1000EVM Firmware issue
Hello Jonathan,I apologize for the issues that you see with the latest GUI/firmware. I documented the procedure for downgrading Firmware in this thread.
View ArticleForum Post: RE: resolution and L inf uH
Hello Florent,angle measurement with 0.1% is feasible with a multi-coil design. However, we currently don't have any design guidelines and minimum size restrictions for such a system.What are the...
View ArticleForum Post: RE: About PLL Lock of DAC5688
Satoshi-san,Once the device is programmed, and the supplies and clocks are stable – the PLL lock time should a function of the loop bandwidth set by the external loop filter. You’d like to have...
View ArticleForum Post: RE: Measure Fluid Conductivity
Hello Fred,I need to correct my last statement; toroid coils are actually a bad coil choice for inductive sensing because they do not emit magnetic fields to the outside. A coil choice that emits a...
View ArticleForum Post: RE: TI high speed equipment
Hi Airat,Please provide your email address so I can send you new configuration files for AFE7225Thanks,Eben.
View ArticleForum Post: RE: TSW3085 EVM Schematic
Hi Jim,I forgot to say the rev. number.That's right and thanks to your prompt reply.Best Regards,Woo
View ArticleForum Post: RE: RE:Connecting Thermocouples to the ADS1148
Hi Dhiren,The diodes you are talking about are for transient protection. The quicker you deal with transients the better, so you do not need to place the diodes after the RC filter.However, remember...
View ArticleForum Post: RE: PCM5102A Variation of Power Dissipation
Hi Don-san,We believe that this reason is the combination of the internal digital interpolation filter option and the device variations.Is our understanding correct?Best Regards,Kato
View ArticleForum Post: About the proximity data of LDC1000
Are the graph and information on relevance (the relation of an inverse proportion?) in the inductance and proximity(distance) data of LDC1000?Thank you for your consideration.
View ArticleForum Post: RE: ADS1258 channel indexing problem in auto-scan mode
Good idea. I will try that!
View ArticleForum Post: RE: About the proximity data of LDC1000
Hi,No, there is no relationship between Rp and L, they are tatally different.Regards, Sunny.
View Article