Forum Post: RE: DSD1793 "External Digital Filter Interface" issue
Hi,I have asked my colleague to look at your post.it may be an issue that the device defaults to the LEFT channel in mono mode. You might need to flip your I2S data.-d2
View ArticleForum Post: RE: PCM2906C Windows 7 default volume control
Hi, Santiago,My understanding is SPDIF is a line-level signal, and thus, volume control won't affect it.-d2
View ArticleClik here to view.
Forum Post: RE: PCM2906C at 48 kHz by default
Hi, Santiago,I believe you can change that here:
View ArticleClik here to view.
Forum Post: ADC1247 3-wire 10k type-2 RTD setup
Hi everybody,Im trying to setup an ADC1247 to use with a 10k RTD. Im going for a three wire configuration. My temperature tange will be 10 C to 80 C. I have found R_comp to be 4.37kOhms but im having...
View ArticleForum Post: RE: temperature stability of LDC1000 converter
For the system at hand one would measure the reading at, say, position 1, and at position 2 - two extreme points.The difference between the measurements is the precision on can achieve.For example, if...
View ArticleForum Post: RE: The question about TSW1400 firmware modification
Hi Eben.scwoo80@etri.re.krThanks for your help.Woo.
View ArticleForum Post: SPI with CSB tied low permanently?
Is it possible to run the LDC1000 SPI by routing the CSB pin to GND.This means the device would be always selected, which is ok because it is the only device in my design.From the manual I see that...
View ArticleForum Post: RE: RE:Connecting Thermocouples to the ADS1148
Hello Mr.BOB. I understand you have been very busy. It would be very helpful if you can give us your feedback to my queries related to my schematic so that I can incorporate changes if any in my...
View ArticleForum Post: RE: Why is the default value of Rp_MIN listed as 0x14? (LDC1000)
After getting my first replys from my LDC1000 I read 0x40 from register 0 ( DeviceID ) however the datasheets says 0x80 is the default.Is register 0 always fixed to 0x80? -> my SPI communication has...
View ArticleForum Post: RE: aic3254 driver problems
hi Don!I used exactly that post to get the driveranyway thanks!
View ArticleForum Post: ADS1282 spi no response
I am trying to interface the ADS1282EVM with my custom development board. When I try to read the registers through SPI, I get all of them to be zero. However I am able to communicate with the...
View ArticleForum Post: RE: AIC3254 Dual Mic Noise Cancelling
Hi, Mark,Unfortunately, we have discontinued support for this application area. Sorry.I wish I could offer you an alternative, but AFAIK, TI is not active in this area.-d2
View ArticleForum Post: RE: GDE on windows8
Hi, Guys,Sorry for the delay. We currently do not have a supported audio processor of this family type.-d2
View ArticleForum Post: RE: ADS130E08 Sample Code
Hello GregI am trying to connect to the ADS130E08 to my Java application using JStyx for Linux, on the java side.Since the EVM Board runs a Styx protocol (from your previous conversations). What then...
View ArticleForum Post: RE: ADS1299 - Pin and Jumper configurations for single-ended EEG...
Hi everybody,i´m trying to measure an EMG signal (Differential Inputs) and I am not sure where to place my electrodes. I assume that I will need 3 Electrodes (2 for muscles and 1 for reference) or 4...
View ArticleForum Post: ADS1299 - EMG - Reference,Bias,Electrodes
Hi everybody,i´m trying to measure an EMG signal (Differential Inputs) and I am not sure where to place my electrodes. I assume that I will need 3 Electrodes (2 for muscles and 1 for reference) or 4...
View ArticleForum Post: DAC7800
Dear all,The microcontroller we are using can send 8-bit data in SPI. It can output 4MHz clock maximum for SPI. Can we use that microcontroller with DAC7800 concerning the clock rate and the number of...
View ArticleForum Post: RE: Reference design for AFE5801
With regard to the AFE 5801 (and presumably that entire series), what is the low frequency response? One can select DC coupling inside the IC (to the PGA?) but is there DC coupling all the way to the...
View ArticleForum Post: RE: ADS7955 / Vdd under the 2*Vref
Hello, Thank you for the reply.I understood. Best Regards,Ryuji Asaka
View ArticleForum Post: RE: ADS131E08 Data read
DRDY is provided for the ADC to communicate data is ready to output. It is not required for use, but not using it risks you getting out of sync with the datarate and missing data. This may happen...
View Article