Forum Post: RE: ADS1212 Byte Zero of CMR Register Changes To FF
Hi Chris,Welcome to the forum! I can see why this is frustrating. Usually this type of event is related to some form of transient. I think that the data output relative to the CMR setting is...
View ArticleForum Post: RE: LDC1000 EVM GUI 1_0_4_1
Hello Amaia,Charles already attached Firmware 0x0208 earlier in this thread. Hello Vittorio,we will investigate the issue with 0x0300. For clarification, are you unable to connect a firmware 0x0300...
View ArticleForum Post: RE: ADS5407 PowerUp Sequence
Hello Richard,Thank you for your reply. I understand it.Regards,Hisakichi Kobayashi.
View ArticleForum Post: RE: ADS42JB69 PowerUp Sequence
Hi Ebenezer,Thank you for your reply. It is usefull answer.Regards,Hisakichi Kobayashi.
View ArticleForum Post: RE: PCM5141/PCM5142 Power Dissipation
Hi Don-san,We have not obtained your reply for this issue and are looking forward to your reply.Best Regards,Kato
View ArticleForum Post: RE: PCM3070 - Audio Mixing configuration
Daniel,For the processing engine to work, BCLK and WCLK must be present either externally or internally. For this case, you would then need to set BCLK and WCLK as outputs. This document describes how...
View ArticleForum Post: RE: Can I tie HVSS to AGND, when I use ADS8634 to convert input...
You can try to switch different channel and you can try to see if channel selection is happening correctly or not.What I meant by kickback, if channel is selected then at sample start and sample end...
View ArticleForum Post: RE: temperature stability of LDC1000 converter
Dear Evgeniy, We have some more questions.How to define precision value for exact system: it is calculated or measured value? If it should be calculated, could you please provide procedure of...
View ArticleForum Post: RE: TSW1400evm firmware download intermittent problem
Hello Jim, May I ask if you can think of any other reason for this problem?Regards,SM
View ArticleForum Post: ADS131E08 Data read
Hi Greg,For interfacing MCU with ADS131E08 currently we are using 4 SPI lines. We will be using ADS in continuous mode. Is DRDY signal necessary?Datasheet says if no data is retrieved from device, DOUT...
View ArticleForum Post: RE: TLV320AIC1110 so much noise
Client saying that capacitors in Out1N, Out1P lines is protection from fool. IC is warming up to 150*С on short circuit in one line. I think it's incorrect schematics.R88 and С62 are using as RC-filter.
View ArticleForum Post: ads1178 getting duplicated point
HiI am working on a data acquisition system based on ads 1178. I am using a stm 32 micro controller to collect the data. But I am getting duplicate points of the waveform (sometimes), in some occasions...
View ArticleForum Post: RE: ADS1212 Byte Zero of CMR Register Changes To FF
Hello Bob,Thanks for the response.I'm running fclk at 2MHz, and SCLK at 200kHz.As far as we can tell, the part still operates fine, it just runs at a new rate. We can configure the A/D without a reset....
View ArticleForum Post: RE: LDC1000 EVM GUI 1_0_4_1
Hello BenYes, even if: with 1.041+0x0300, some kind of connection happens (the plot was running), with 1.030 + 0x0300 I was not able to get any connection.Best RegardsVittorio
View ArticleForum Post: RE: PCM5122 Example Filter Settings?
Thanks Dafydd,one more question from customer...Theissue I am having is passing sample rates of 192K. I removed the I2Sjumpers to isolate the PCM5122 from the rest of the circuit. I’musing an...
View ArticleForum Post: RE: The question about TSW1400 firmware modification
Hi Woo,Provide your email address and I will forward you the source codeThanks,Eben.
View ArticleForum Post: RE: TLV320AIC3110 circuit suggestions
Hi, Anil,Thanks for posting. I have highlighted your post to my colleague who is familiar with this device.-d2
View ArticleForum Post: RE: Why is the default value of Rp_MIN listed as 0x14? (LDC1000)
You are right. The register default value of Rp_min is invalid. This value must be changed from default during the initialization sequence.
View ArticleForum Post: RE: aic3254 driver problems
Hi, Maxim,We have some info about drivers posted on another thread. You can find it here, but I think it will not help you very much, unfortunately...Maybe someone else on the community has run across...
View Article