Forum Post: RE: ADS1288: ADS1288
Hi Lkhagvajantsan, The ADS1285 has been specifically designed to interface with geophone sensors while consuming very small 5mW while providing very high dynamic range. It is a good choice for seismic...
View ArticleForum Post: RE: TSC2046E: How to reset when power up
Hi Higa-san, This device has few settings that would require a factory reset, you can see in the tables 3 and 4 from the datasheet that the device has one control byte which allows the user to set the...
View ArticleForum Post: RE: ADC3664EVM: DCLK and Sampling Clock
Hi Rob, Thank you for your reply. I got the insertion position for BPF your showed. Is 2dBm(0.796Vpp sinewave) max for DCLIN(650mVpp max)? The VID for CLKP/M for sample clock is 1Vpp(typ) and...
View ArticleForum Post: RE: ADS131M06-Q1: transition response
Hi Bryan, Dala, I will send this topic via email. Best Regards, Yuki
View ArticleForum Post: RE: ADS1120: ADS1120: Reading Ktype temparature with cold junction
Hi Burak, The following document explains in detail how to perform K-type thermocouple measurements with the ADS1120 and how to perform cold junction compensation: K-type thermocouple measurement...
View ArticleForum Post: RE: ADC3664EVM: DCLK and Sampling Clock
Hi TTD, The CDC on board clocking chip does not support all sampling clock rates. What is the sampling clock rate you are using? 437.5MHz? I will set this up tomorrow on in the lab to check. If there...
View ArticleForum Post: RE: ADS1220EVM: ADS1220EVM using Arduino.
Hi Arjin, Are you attempting to use the ADS1220 on the EVM without the controller on board and with your own Arduino? If so, not all of the ADC SPI connections go to the JAC connector, some of them go...
View ArticleForum Post: DDC118: 20CH current input ADC for PHOTODIODE Sensors application
Part Number: DDC118 Tool/software: Hello, My customer is looking for a current input ADC for Photodiode Sensors application with the following conditions. - No. of Input channels : 20 or more -...
View ArticleForum Post: RE: DAC39RF10EVM: No Output from GBTCLK1_FMC_p/n
Hi Chase, Thank you for your prompt response. After changing Register 0x12F from 0x50 to 0x51, BGTCLK1_FMC is now being output. I appreciate your help. Best regards, tabe
View ArticleForum Post: RE: ADC3664EVM: DCLK and Sampling Clock
Hi Rob, Sorry for confusing the slightly different parts number between ADC36 6 4 and ADC36 4 4. I already have a ADC3664EVM(SLVDS) and ADC3644EVM(DDR CMOS) .has been shipping now from TI(I don't have...
View ArticleForum Post: ADC3223: Regarding Conversion Accuracy and Reference
Part Number: ADC3223 Tool/software: Dear Specialists, My customer is considering ADC3223 and has questions. I would be grateful if you could advise. ---Questions (1) Regarding ADC3223 datasheet, there...
View ArticleForum Post: DAC39RF10EVM: Lane Mapping Issue – Only 8 Lanes Enabled
Part Number: DAC39RF10EVM Other Parts Discussed in Thread: TSW14J59EVM , Tool/software: Hi, I am testing the DAC39RF10EVM by connecting it to the TSW14J59EVM and configuring it through the...
View ArticleForum Post: RE: ADS131E08: How to Suppress Industrial Frequency Noise in...
Hi Bryan I am sorry that I failed to describe it clearly, let's forget the item of target signal for a moment and consider it as a noise for testing the ADC device, after designing the ADC test board...
View ArticleForum Post: RE: ADS131E08: How to Suppress Industrial Frequency Noise in...
such as optimizing the ADC input front-end circuitry or redesigning the ADC driver power supply.
View ArticleForum Post: ADS131E08: RREG register is not working
Part Number: ADS131E08 Tool/software: Hi team, When reading register information with the RREG command, after issuing the SDATAC command according to the datasheet, I am trying to read the contents of...
View ArticleForum Post: ADC3669: ADC3669 LVDS INTERFACE DEBUGGING
Part Number: ADC3669 Tool/software: My project uses ADC3669 for data acquisition, and I am currently debugging the parallel LVDS interface communication between ADC and FPGA to receive ADC data. Like...
View ArticleForum Post: RE: DAC38J84EVM: Query regarding Zero Delay Mode in LMK04828
Prateek, I have asked the clocking team to support you on this configuration.
View ArticleForum Post: RE: ADC3562: Regarding AINM pin processing when using AD...
Hi, I have a question about the driver THS4541 for ADC3562. Will the THS4541 shorten the life of the device if it repeatedly goes into an unbalanced circuit state where normal negative feedback does...
View ArticleForum Post: RE: AMC131M01: Issue with DCDC Output When Controlled via SPI
Hi Omkar, The DCDC_Freq selection in Table 8-31 is actually incorrect. It's from a previous revision that was missed when updating the datasheet. Please refer to Table 8-3, the one I responded with...
View ArticleForum Post: RE: ADS1220EVM: ADS1220EVM using Arduino.
I've already connected both JAC and JDB. If I remove JP8, the 3.3V supply to the DVDD of the ADC is disconnected, so I would need to provide it externally. This external supply to the ADC would then...
View Article