Forum Post: RE: ADS114S08B: Logic output types
Hi Bryan, Thank you very much for your reply. Is my understanding correct that DIN, DOUT, and SCLK signals can be shared via same bus, and CS and DRDY signals should be used independently each devices...
View ArticleForum Post: RE: ADS127L11: DRDY-pin is not getting low
Hi Keith, Than you for your reply. If I keep start "high" without sending any SPI configuration data, I am getting DRDY signal 400KHZ. Also re-checked CAPA (pin 2) 1.62V CAPD (pin18) 1.31V. Looks like...
View ArticleForum Post: RE: ADS1299: ADS1299 - 2 ICs Settings (SRB, BIAS)
I would like to share my schematic for clearing the doubts ,It's confidential so can you please share mail ID so that I can attach my schematic.
View ArticleForum Post: TI-JESD204-IP:ADC09SJ1300
Part Number: TI-JESD204-IP Other Parts Discussed in Thread: ADC09SJ1300 Tool/software: Hello, experts. When I tried the operation of subclass 0 under the following conditions, I encountered a problem...
View ArticleForum Post: RE: TI-JESD204-IP:ADC09SJ1300
I can also send you the ADC and FPGA block diagrams. I will send you a separate email if you don't mind. Thank you.
View ArticleForum Post: RE: ADS1299: ADS1299 - 2 ICs Settings (SRB, BIAS)
As we told earlier, we are using one ADS1299 for EEG(Unipolar- 8 Positive electrodes, 1- Reference electrode(SRB1)) and other for EMG(Bipolar - 8 positive electrodes, 8 negative electrodes) and 1...
View ArticleForum Post: RE: DAC8742H: Does DAC8742H has passed the physical layer test of...
Hi Joseph, how 's thing going? Do you able to verify my test? Just let me know if you need anything, such as the testing signal. Best
View ArticleForum Post: RE: ADS8556: We would like to set the "CR" only once, retain the...
Hi Samiha-san, Thank you for your reply. I'll share your answer with the customer. When the customer has an additional question, I consult you again. I appreciate your great help and cooperation. Best...
View ArticleForum Post: RE: ADS7958: MUX staying in ch0 and not switching further
Hi Joel, Sorry for the delayed response, Yes sometimes the mux works but as you said channel 0 data will come on channel 1 and so on, The capture that I've given explains that, We tested with ADS7959...
View ArticleForum Post: ADC3562: state of SCLK between packets of SPI communication
Part Number: ADC3562 Tool/software: Hi, The datasheet of ADC3562 show the following timing chart in "8.5.2 Configuration using the SPI interface". Where, the figure shows that SCLK is low before...
View ArticleForum Post: RE: AFE58JD48EVM: Query regading the ADC sample MSB bit
Hi Sachin Thanks for the input, we changed the source signal. Now we are generating the input signal from FPGA itself from same device clock and now we are not getting this this. But, we are getting...
View ArticleForum Post: RE: ADC3649: ADC3649 availability
Hi Rob, thank you - I could see that. Is there a way to tell when these items will be on stock again? Regards, Alex
View ArticleForum Post: RE: ADC09QJ800-Q1: Initialization
Hi Eric, Why do you think the bit is not going to 1. In step 3 of the initialization sequence I am polling bit 0 of INIT_STATUS and this bit is going to 1. What could be the reason that bit 2 of 0x208...
View ArticleForum Post: RE: ADC34J23EVM: Unable to configure ADC & LMK04828 using ADC3000...
Hi Rob, Thank you for the detailed troubleshooting steps. The 100 MHz oscillator is on board and powered up. I have measured on pin 44 of the LMK (Oscin_n) and confirm that the clock input is present:...
View ArticleForum Post: AMC131M03EVM: AMC131M03EVM
Part Number: AMC131M03EVM Other Parts Discussed in Thread: AMC131M03 Tool/software: Hi I'm having trouble getting "AMC131M03 EVM.exe" running. I've installed a 32 bit LabView runtime from 2019 to...
View ArticleForum Post: RE: ADS114S08B: Logic output types
Hi Akira Sugimoto, [quote userid="610521" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1468879/ads114s08b-logic-output-types/5639069#5639069"]Is my understanding...
View ArticleForum Post: RE: ADS1299: ADS1299 - 2 ICs Settings (SRB, BIAS)
Hello Rajasree - you can send your schematic to ads129x-support@list.ti.com . Yes, the same ground would be used for both applications. Regards, Ryan
View ArticleForum Post: RE: ADC3649: ADC3649 availability
Hi Alex, They should both be in stock. Are you seeing one or both is not? Thanks, Rob
View ArticleForum Post: RE: ADS1298ECGFE-PDK: Support software for Win10/11
Hello Takumi-san, The same version of the ADS1298ECGFE-PDK software can be used on Windows 10 and Windows 11. Regards, Ryan
View ArticleForum Post: RE: ADC3562: state of SCLK between packets of SPI communication
Hi, I have requested any information on this from the design team. Regards, Geoff
View Article