Forum Post: RE: ADS1299LV password request
Thank you, I have received。Have the AFE44x0EVMspo2 the GUI LABVIEW source code is download ????, Because the execution and found a lot of BUG
View ArticleForum Post: AIC3204 Clocking and interfacing with dsPIC33
Hi everyone,I'm working on a project to interface the AIC3204 with a dsPIC33fj64mc802 processor, the interface is i2c. I have evaluation module for the AIC part and same for the dsPIC33fCurrently I...
View ArticleForum Post: RE: PCM1808 ADC Full Scale Voltage Range
Hi, Don-san,Thank you for your information.But we would like to know the full scale voltage range of delta sigma adc.Although this value is described as 3Vpp in the data sheet, we understood it as...
View ArticleForum Post: RE: ADS1015 MUX switching
Follow up question. We are working with the ADS1015, and we can set the gain to plus/minus some voltage, which subsequently correlates to temperature. Let's assume our sensor has a range of -40 to +125...
View ArticleForum Post: RE: Need response concerning ADS1015 protocol
Verified, that did the trick. Of course, the key is also handling endianness correctly, but this is easily dealt with in thin verniers.
View ArticleForum Post: RE: TLV320AIC3204: Help needed configuring secondary audio bitclk
Hi Rob,First, see correction to my previous post.I cannot tell you what the designers had in mind at that moment, but keep in mind the amount of pins available for multi-function purposes. There are...
View ArticleForum Post: RE: Need help with ADS8332 chip.
Hi Jeward,Welcome to the forum!There are two ways to configure the CFR on the ADS8332 - with user-supplied data or with default data.User-specified values are loaded into the CFR using a 0xE command...
View ArticleForum Post: RE: AFE4490 EVB source code for MSP430F5529
I am working on a design with the AFE4490 using the MSP430F5529. Would it be possible to get the source code for the eval board?Thanks!
View ArticleForum Post: TLV320DAC3100
Hi Team,Please advise how my customer can connect 2 chips (Customer ASIC & AM/FM chip) that both connect to the I2S interface.If you look at page 58 at the TLV320DAC3100 data sheet you can see they...
View ArticleForum Post: RE: ADS1292 (VREFP+VREFN)/2 Available and bufferable?
The plan is to buffer it through the 'spare' opamp from the RLD. The input impedence wasn't specified in the datasheet to my knowledge, but the reference circuits led me to believe it was in excess of...
View ArticleForum Post: RE: NEED INFORMATION- DAC7725NBG4
Jayakumara,We do not have this information at this time. Our only choice would be to pursue getting the device modeled and that may take some time and is not a completely trivial effort. If that's a...
View ArticleForum Post: RE: TVP5151am1 BT601 output Discrete syncs mode hsync and vsync...
I have just checked and it appears that you are correct. The closest I could configure the alignment was 74ns which is one clock period at 13.5MHz. This was with a HSyncStart = 12 setting.I don't think...
View ArticleForum Post: RE: ADS1147: SELFOCAL command
Hi Max,Both methods should give similar results. If not, then there is a noise source contributing to the difference.Best regards,Bob B
View ArticleClik here to view.
Forum Post: RE: cannot install driver for ADS1298 to Windows Vista....
Thank you for response. I did exactly how you discribed it. I knew how to installed drivers (I have MS in Comp. Sci). I got the message:
View ArticleForum Post: RE: High speed differential line receivers
Hey Richard ,How are you ? Hope you are doing well...Here I discussed with my project guide ..he told speed 3MSPS is ok which he means I can't select A/D converter less than 3msps it is a margin ... So...
View ArticleForum Post: DAC3484 Questions Part 2
Hi,I've found "DAC3484 Questions" topic on forum, but it didn't contain the questions I would like to ask. It also looked "closed" to me, so I opened this thread, I hope it doesn't go against the forum...
View ArticleForum Post: RE: ADC12D1800RF can't configure DES mode
Hello Marjorie,Thanks for your quick response. In fact yes I've tried that, but I see no changes in the plot e.g. if I have a tone at 700MHz, in non-des mode its ok, and in des-mode is at 1400MHz..That...
View ArticleForum Post: Fast data transfer with ADS1605 and TMS320C6416 / readblock...
Hello at all,My name is Christoph Winterholler and I am doing my diploma project with an ADC and a DSP.I use the following hardware: ADS1605EVM (5MSPS/16Bit) with 5-6KInterface Board and TMS320C6416DSK...
View ArticleForum Post: RE: Issue with TLV320AIC3106 Codec DOUT pin - No data
Hi, On checking the signals by probing, we see the BCLK signal , but no WCLK and DCLK signal on recording. Can the codec be configured to send the data based on the bit clock and data len per...
View ArticleForum Post: RE: PCM5122 DAC as I2S master troubles with PLL mode
Thank you Dafydd for trying this solution,I'm pretty sure that each line of your script means something likewrite 98 <value> <register>but I was wondering what 98 means. Is that correct?...
View Article