Forum Post: RE: DAC38RF82: SERDES PLL won't lock
(Please visit the site to view this file)(Please visit the site to view this file)Scott, Please see the GUI settings used in the attached presentation and the attached configuration file. These were...
View ArticleForum Post: Compiler/ADS1298: ADS1298
Part Number: ADS1298 Tool/software: TI C/C++ Compiler Sir, I have started work on ADS1298 Ic with details studies of it's data sheet for EMG measurment and also made its circuit withhelp of data sheet....
View ArticleForum Post: RE: AFE5818EVM: connect with TSW1405 for simultaneous 8 channel...
Hi Kiran, Yes, TSW1400EVM can capture all 16 channels' data with the AFE5818 's clock speed (according to setting) and saves into the on-board memory at the same speed. Since all the data (in the...
View ArticleForum Post: RE: ADS1282EVM-PDK: Anything in the EEPROM would prevent me from...
Hello Tom and Chris Buying a blank EEPROM and replacing it in the ADS1282EVM unit I have is something I would do if I need to. For me it is key to know if I can go on with my baseline development...
View ArticleForum Post: RE: DAC161S997: COMMUNICATION ERRORS USING DAC161S997
Hi Kobena, Any update on this thread? Thanks, Garrett
View ArticleForum Post: RE: ADS1299: Analog EEG signals output needed
Hi Venkata, Thanks for your post and welcome to the forum! If you take a look at section 9.3.2.4.1, you will see that unfortunately the ADS1299 does not have a differential (P-N) output after the PGA,...
View ArticleForum Post: RE: Compiler/ADS1299: ADS1299
Hi Nikitha, Thanks for your post! 1) Does the ID register read back correctly? 2) Are you following the correct start-up sequence in section 10.1.2 and 11.1? After the power-on reset is complete, /DRDY...
View ArticleForum Post: RE: AFE5818: Require 16ch AFE5818 TX EVM W/STHV748 documents details
Hello Kiran, I am closing this post since we have taken this discussion offline.
View ArticleForum Post: RE: ADS1256: ADS1256 and TM4C129 SSI communication issue
Hi, Thanks for getting back to me. I made some changes and ran the code. It seems one of the issue is the sclk frequency used. It seems I can read back the values of the registers 01h,03h and 04h. The...
View ArticleForum Post: RE: LMP90080: Single-ended RTD solution
Hi Mihir, Thanks for your post and welcome to the forum! I'm not sure what you mean by "7-single ended RTD solution" can you elaborate or draw a diagram if necessary? Why do you want to drive 10mA...
View ArticleForum Post: RE: AFE58JD28: fs/2 spur
I actually think it is sampling interleaving since this ADC has an odd and an even circuit sampler per channel. Datasheet page 59. this thread is similar e2e.ti.com/.../584724 and there are others on...
View ArticleForum Post: RE: RTOS/ADS7142: ADS7142 is stuck and does not emit new alerts
Hi Oleh, Have you resolved your issues?
View ArticleForum Post: RE: ADS124S06: ADS124S06 Unused REFN0
Hi Masa-san, I'm sorry as I misunderstood your original question. In your block diagram you have something connected to REFN0 and I initially thought the REFN0 pin was floating. Using the PSW bit in...
View ArticleForum Post: RE: ADC12DJ3200EVM: FMC+ to FMC adapter for ADC12DJ3200EVM
Hi Tom These aren't currently available for direct ordering. If you can provide shipping information (address and phone number) I can arrange to have 1 or 2 adapters shipped to you. Best regards, Jim B
View ArticleForum Post: RE: ADS114S08: Data output from ADS goes to zero intermittently
Hi Amol, Your schematic did not make it through with your last post, can you re-submit it?
View ArticleForum Post: RE: ADS124S06: ADS124S06 Protection diodes on 3-wire RTD typical...
Hi Masa-san, The diodes are not a requirement, however you must protect the analog inputs so that the Absolute Maximum Ratings for input voltage and current are not exceeded. In the datasheet circuit...
View ArticleForum Post: RE: ADS1294R: Bits Flickering in Lead Off registers
Hi Vignesh, Thanks for your post! This is an interesting issue, my immediate thought is that there is a degradation of some sort in your signal chain and that the first case from Issue No1 and Issue...
View ArticleForum Post: RE: ADS114S08: Data output from ADS goes to zero intermittently
Sorry - I see that it went with the split thread.
View ArticleForum Post: RE: ADS124S06: ADS124S06 RDATA command read from buffer
Hi Masa-san, There is an internal conversion result register and an output buffer for the ADS124S06 . When the RDATA command is issued the last completed result will be copied from the conversion...
View ArticleForum Post: RE: ADS124S06: ADS124S06 WREG command
Hi Masa-san, The ADS124S06 differs from the ADS1248 in this operation. Communication is possible with the START pin low with the ADS124S06 where the ADS1248 cannot write registers and is limited to a...
View Article