Forum Post: ADS127L01: SPI DOUT does not give any data
Part Number: ADS127L01 Hello, I would like to able to synchronize when to read the ADC data using the SPI command. I am working with the following setting: - START pin connected to ground permanently -...
View ArticleForum Post: RE: ADC12D1800: Recommended power-up sequence for NON-DES mode...
Hey, thank you for the thorough reply. We set the NDM bit to logic low '0' - DEMUX mode (i.e. We use both DI and DID for sampling the I channel). About the sampling logic, as mentioned, the TPM mode...
View ArticleForum Post: RE: ADS1282EVM-PDK: Anything in the EEPROM would prevent me from...
Hi Martí, I don't think so, but if you want to be sure you can try removing the EEPROM from the ADS1282EVM and modifying the INI file, as Tom suggested.
View ArticleForum Post: ADS124S06: ADS124S06 REFP1 and REFN1
Part Number: ADS124S06 Dear Sir, I would like to make sure that ADS124S06 can have two Differential Reference Input. The datasheet Section 9.3.3 states that "the ADS124S08 offers two differential...
View ArticleForum Post: RE: DAC9881: Power-Supply Sequence
Duke-san, Thank you for your reply. What is the meaning of "device corruption" ? Is it destruction of device? Or is it that it doesn't work right? Best regards, itabi
View ArticleForum Post: RE: ADS124S06: ADS124S06 REFP1 and REFN1
Hi Masa-san, I can confirm to you that ADS124S06 does offer two differential reference inputs (REFP0/REFN0 and REFP1/REFN1). As you noted, the difference between ADS124S06 and ADS124S08 is that...
View ArticleForum Post: RE: ADS124S06: ADS124S06 REFP1 and REFN1
Hi Joachim Thank you very much for your confirmation. Masa
View ArticleForum Post: RE: ADS124S06: ADS124S06 Digital Domain at PGA=64 and 128
Hi Masa-san, there is no disadvantage in using gains of 64 and 128 on ADS124S06 . The advantage of the higher gains will be that you achieve lower/better input referred noise as shown in the noise...
View ArticleForum Post: ADS124S06: ADS124S06 Reference Buffer
Part Number: ADS124S06 Dear Sir, May I ask if Reference buffer is recommended to be enable at RTD ratiometric application? Best regards, Masa
View ArticleForum Post: ADS114S08: Data output from ADS goes to zero intermittently
Part Number: ADS114S08 I am trying to read from ADS114s08b 6 channels with interval of 500mSec (Also tried 100mS/200mS/1000mS intervals)Sometimes the data is read properly for 3-4 mins. But stops...
View ArticleForum Post: RE: DAC81416: DAC81416 Vcc positive power minimum requirements
Hi Andrey, Could you please provide information on the points below: 1. What is the operating temperature range? 2. What is the type of load or max load? Will you be drawing 1mA from all channels...
View ArticleForum Post: RE: ADS124S06: ADS124S06 Reference Buffer
Hi Masa-san, this depends a little on the circuit implementation, but in general it is recommended to have the reference buffers enabled to reduce the input currents flowing into the reference inputs....
View ArticleForum Post: RE: ADS124S06: ADS124S06 Reference Buffer
Joachim, Thank you very much for your answer. Masa
View ArticleForum Post: RE: DAC38J84: 4 independent outputs
Hi Kang, thanks for the hint. I completely missed the coarse mixer. regards, Domenico
View ArticleForum Post: ADC34J44: compatability with KU040
hi can the ADC34J44 EVM be connected to the KU040 , i.e. use the KU040 as FPGA board (FMC connector, SW, etc.)? thansk a lot in advance KR Vincenzo
View ArticleForum Post: RE: ADS1148: Internal Reference voltage not switching ON
Hello Alex, Thank you for your guidance, this solved my issue. Best regards, Balazs
View ArticleForum Post: ADC161S626: The amount of characteristic change due to aging
Part Number: ADC161S626 One of my customers wants the following data strongly. Please tell me about the following devices. ・ADC161S626CIMME/NOPB Could you please tell the amount of characteristic...
View ArticleForum Post: AMC1204: What integrator time constant does the modulator have?
Part Number: AMC1204 Hello, To verify my measurement results and unterstand the bandwidth limitations of your modulator and my filter, I want to simulate the modulator as perfect as possible. Therefore...
View ArticleForum Post: RE: DAC37J82: Can't detect DAC condition from registers
Jim, Sorry for the delayed response. I'm sure the company has an NDA in place with TI, but I do not believe that I am specifically named. Let me know how to proceed. My understanding regarding the FIFO...
View ArticleForum Post: AMC1304L25: AMC1304L25
Part Number: AMC1304L25 Hi Experts, We are using AMC1304L25 Reinforced Isolated Modulator With LDO Regulator, ±250mV Input, and LVDS Interface fro one of our design. For performing Signal Integrity...
View Article