Forum Post: RE: AMC7812: seeking support for I2C communication in AMC7812
I had tried this one also, by setting Iconv bit once, but it didn't resolve my problem....A7 is the read register for adc 4 data.(0x27+0x80=0xa7). I just tried with two registers adc 4 and adc 5 and I...
View ArticleForum Post: RE: ADS5296A: Full scale ramp test pattern output format
Hi Niall, How are you? We are using TSW1400EVM to capture the ADS5296A output data. Also we already verified using both 10bit mode and 12bit mode register setting and received the output data using...
View ArticleForum Post: RE: ADS1282EVM-PDK: Anything in the EEPROM would prevent me from...
Hi Marti, Technically, no - the EEPROM on the ADS1282EVM-PDK just contains detail on the when the board was built and tested. That being said, the ADCPro tool does read that EEPROM to try and ensure...
View ArticleForum Post: RE: ADS5296A: Full scale ramp test pattern output format
Hi Chen, Ok thanks, this answer my question. Now that I know what to expect from the output pattern I can look for the issue. I will write the values mentioned to the registers next week and see if...
View ArticleForum Post: RE: ADS1278: How to configure the pins to send data on SPI interface
Hello Bartosz, You are correct; there are no registers to program in this part. You just need to connect the different configuration pins high or low for the different modes of operation. The following...
View ArticleForum Post: RE: ADS131A04EVM: Startup procedure
Michael, I don't see any issues in the timing from the last plot. I did pull out the Saleae file, and this is what the plot looked like: For a closeup of the second and third frames, you can see it...
View ArticleForum Post: RE: ADS8168: Drive capability of REFP? Or use REFIO?
Hello Phil, Welcome to the TI E2E Community. The correct place to connect to the internal reference is the REFIO pin. The internal reference has a 1kohm resistor in series with its output and the REFIO...
View ArticleForum Post: ADS1247: Source Differential Voltage Changes when Connected to ADC
Part Number: ADS1247 I am using the ADS1247 ADC with the AD8476 differential amplifier as the source to the ADC input. I am supplying each with 3.3V, but they are independent (both supply and circuit...
View ArticleForum Post: RE: ADS131A04EVM: ADS131A04EVM
Kost, I think I have a solution for your script loading problem. I believe that the software is looking for a "user" directory for the script. When the software doesn't find the directory, it doesn't...
View ArticleForum Post: RE: ADS8168: Drive capability of REFP? Or use REFIO?
Great! Buffer added... Thanks!
View ArticleForum Post: RE: DDC232: Which Microcontroller for DDC232
Hi Khoi, Sorry for slow reply but as Chen explained I was traveling... Anyhow, when you say 100+ sensors I guess you mean that you will need 3 or 4 DDC232 , right? As explained on the DS (start on pg...
View ArticleForum Post: RE: ADS52J90: Multiple synchronization
Hi Kuramochi-san, (Please visit the site to view this file)Here is the attached more detail explanation for you. It can show align at falling edge and 1 clock cycle gives sufficent margin for hold and...
View ArticleForum Post: ADS1218: Query regarding the External clock
Part Number: ADS1218 Hi Team, I am using ADS1218Y with a external clock of frequency - 2.4576MHz/ Amplitude - 4Vpp from a function generator. I was able to successfully use all functions like...
View ArticleForum Post: RE: ADS1247: Source Differential Voltage Changes when Connected...
Hi Jim, Hard to say exactly what might be going on without getting into the circuits and measuring various points around the diff amp and ADS1247 , but I suspect slight differences in the ground...
View ArticleForum Post: RE: ADS1218: Query regarding the External clock
Hi Makesh, There is a table on page 2 of the datasheet that lists the ABS MAX voltage that you can apply to the ADS1218 . In short, you can't exceed AVdd or DVdd on any input by more than 300 mV, so...
View ArticleForum Post: Compiler/ADC12DJ3200: ADC12DJ3200 with KCU105 : Can I make my own...
Part Number: ADC12DJ3200 Tool/software: TI C/C++ Compiler Hi guy, I'm interested in the ADC12DJ3200 with KCU105 for my research. but I have some question. 1. In the firmware has a external trigger for...
View ArticleForum Post: ADC084S021: ADC084S021 example code
Part Number: ADC084S021 Hello, My customer wants to get the driver routine of ADC084S021 , wants to confirm the driver routine and source code of the hardware (has sent a GUI link to the client)....
View ArticleForum Post: RE: ADS1148: Unstable dataout value in case of input=±0.1mV
Alexander san Thank you so much for your reply! Now, we try to get these information from the our customer. However, under complicated situation with the customer, we can not get the information which...
View ArticleForum Post: TSW14J57EVM: TSW14J57/58
Part Number: TSW14J57EVM Hi What are the main differences between TSW14J56 and TSW14J57?
View ArticleForum Post: RE: ADS1282EVM-PDK: Anything in the EEPROM would prevent me from...
Would there be any problem if I remove the EEPROM from my design?
View Article