Forum Post: RE: ADC34J44: compatability with KU040
Vincenzo, We have never used the KU040, but if it has the serdes lanes, SYSREF, clock, and SYNC signals all routed per the ANSI/VITA 57.1 FMC standard, I believe the ADC can be used with this platform....
View ArticleForum Post: RE: TSW14J57EVM: TSW14J57/58
Eli, The TSW14J57 supports 16 serdes lanes at rates up to 15Gbps, uses an Arria 10 device, and requires 12V input power. The TSW14J56EVM only supports 8 serdes lanes at rates up to 12.5 Gbps, uses a...
View ArticleForum Post: ADS131E08EVM-PDK: Not able to see correct ADC input on ADS131e08...
Part Number: ADS131E08EVM-PDK Hi, I have ADS131E08 EVM PDK kit. When I gave 50 mVpp input through Function generator to Channel 1 on the kit. It is giving distorted output on scope. For reference...
View ArticleForum Post: RE: DAC37J82: Can't detect DAC condition from registers
Lance, You could try using the PAP alarm. if you set the threshold to a low value, if the DAC is operating, this should set the PAP alarm (address 0x6C). If you set the protection to no attenuation...
View ArticleForum Post: RE: Compiler/ADC12DJ3200: ADC12DJ3200 with KCU105 : Can I make my...
Pachara, We are looking into this for you. Regards, Jim
View ArticleForum Post: RE: ADS8168: No SDO response from ADS8168
Hello, I now was able to connect /RST (pin 29) to 3V3 (pin 30) and the ADC now answers via SPI! Thanks again for you help, kind regards, Markus
View ArticleForum Post: ADS4126: Similar functionality part
Part Number: ADS4126 Hi team, I know as of yet there are no plans to NRND the ADS4126 , however I have a industrial client that plans to go into production next year and carry on for 5-7 years. I was...
View ArticleForum Post: ADS5294: ADS5294EVM
Part Number: ADS5294 Hi, we are using 8 channel ADC = ADS5294 EVM along with ADC-to-FMC adapter to interface with KC705 board The FMC connector voltage should be same at both the end but the KC705 FMC...
View ArticleForum Post: RE: ADS1148: Internal Reference voltage not switching ON
You're welcome Balazs, please let us know if you have additional questions!
View ArticleForum Post: RE: DAC37J82: Can't detect DAC condition from registers
Jim, I read the PAP section (7.3.18). There, it says "...if the data clock is lost, the FIFO would automatically generate a single tone signal..." Does "single tone" actually mean "single value" (i.e.,...
View ArticleForum Post: RE: AMC1304L25: AMC1304L25
Hello Ashish, Thanks for your post! Unfortunately we do not have an IBIS model for the AMC1304, however we do have one for the AMC1305L25 , located here: http://www.ti.com/product/ AMC1305L25...
View ArticleForum Post: RE: ADS1282EVM-PDK: Anything in the EEPROM would prevent me from...
Hello, Thank you very much for your answers. The inputs are very much appreciated. I tried removing the EEPROM on the ADS1282EVM-PDK and it didn’t work. I did as follows: 1. Desolder lead 8 (power) of...
View ArticleForum Post: RE: AMC1204: What integrator time constant does the modulator have?
Hi Julia, Thanks for your post and welcome to the forum! Unfortunately I cannot give out proprietary information not spec'd in the datasheet on a public forum. If you have additional questions about...
View ArticleForum Post: ADS7223: CID in full clock mode
Part Number: ADS7223 Hello Team, we are using the ADS7223 in full clock mode. Our idea was to read the CID with each conversion for plausibility testing. It seem that in this mode the channel number...
View ArticleForum Post: RE: ADS4126: Similar functionality part
HI Carlos I have notified the ADS4126 expert regarding this post. He will provide a more detailed response soon. Best regards, Jim B
View ArticleForum Post: RE: ADS62P44EVM: Configuration for DC Coupling
Hey Mohsin, I think pretty much all of our ADC's are designed for AC coupling but offer DC coupling through an Amplifier as an alternative. Similiar to the EVM you are currently using. Yusuf
View ArticleForum Post: RE: ADS114S08: Data output from ADS goes to zero intermittently
Hi Amol, Thanks for your post! From your waveform captures, there seems to be a significant amount of noise on the lines. Can you probe your power supplies to see if the same noise is present? The...
View ArticleForum Post: RE: ADS4126: Similar functionality part
Carlos, We do not have many options. Does the part have to be a single converter? Does the minimum sample rate have to be 160MHz? Regards, Jim
View ArticleForum Post: RE: DAC161S997: COMMUNICATION ERRORS USING DAC161S997
Hi Kobena, I don't see any issue with your schematic that would cause this issue. One thing to note if you are using HART the 1uF capacitor across Loop+ and Loop- is too large and will attenuate the...
View ArticleForum Post: RE: DAC8728: Wrong output is seen at power-up
Hi Masanori, Apologies for the delay. There is a power-supply sequencing requirement for this device. It is described on page 41 of the datasheet. Please check whether you are following that or not. I...
View Article