Forum Post: RE: LMP91000EVM with H2S MICROceL HS
Hi Domenico,Thanks for you answer.If I want to make a differential measurement between C1 and C2, can I re-use the ADC161S626CIM which is present on the LMP91000EVM ?I would unsolder R4 and connect C1...
View ArticleForum Post: RE: AFE7222 / about AUX DAC, 8-sample FIFO mode and LVDS...
Hi Ryuji,+/- 100mV are the max and min data thresholds respectively for AFE7222 .Thanks,Eben.
View ArticleForum Post: RE: Frequency ranges for TI TLV320AIC3106 codec
Thanks for your reply. We tried a few things after this post. Fs = 96kHz.1) Tried inputting 20kHz into codec and looking at output on scope => 20kHz Tried inputting 42kHz into codec and looking...
View ArticleForum Post: RE: Link to ads1258-adcproplugin-2.0.0.exe is broken. Could I get...
Do you (or your company) have a firewall setting that may be preventing the download?It appears to be OK to download the file on our end, but we will continue to investigate.
View ArticleForum Post: RE: ADS5407 Logic Levels
Hi,I consulted with our design team for this device and with the data sheet author. It was not our intent to have an 'LVDS' input buffer that required such a large swing that it could not be driven by...
View ArticleForum Post: RE: tlv320aic3256 codec apparently "crashes", resulting in I2C...
We have not seen this problem on our platforms. This device has been in use in very large volumes for years and I'd expect to have encountered this problem if it were an inherent bug of the AIC3256.Are...
View ArticleForum Post: RE: PCM9211 Unlock Condition of CDR
Hi Dominik-san,Thank you for your quick reply.I understood.Best Regards,Kato
View ArticleForum Post: RE: Two Toned Testing ADC12J4000
Hi JillPlease refer to the user guide for High Speed Data Converter Pro, available here: http://www.ti.com/lit/pdf/slwu087Section 3.6.3 describes the Two Tone setup and display.The ADC Input Target...
View ArticleForum Post: RE: TLV320ADC3001: Confirm the usage for sensing application.
Hi,Thank you for your comments.Please let me confirm the following question.[Question.1]Can customer use this device with 300 sps?Regarding to the datasheet, the minimum sampling rate is 8ksps.If you...
View ArticleForum Post: RE: ADS1252EVM - Where can I find one?
Hi James,what are the features or key parameters of the ADC you are looking for and what is your application?ADS1252 and ADS1240 are quite different devices.You might want to consider one of our more...
View ArticleForum Post: RE: ADS1120 / Single-shot mode
Hi Bob-san, I can understand.I really appreciate for your support! Best regards,Yaita
View ArticleForum Post: RE: LM49352 registers clarification
0x52h is Synth_Denom (Denominator). You can select 128 or 125. Then in Synth_Num you can choose the numerator to get ratios like 96/128 or 96/125 ..... This is when you use the audio ports and want...
View ArticleForum Post: RE: ADS1120 / supply current in single-shot mode
Hi Bob-san, Thank you for your detail&clear explanation.I appreciate for your support. Best Regards,Yaita
View ArticleWiki Page: ADS1282EVM-PDK
Issue:When I load the ADS1282EVM plug-in from EVM drop down menu then after series of messages I got the following messages, what is wrong?"Download failed ... reset the hardware""The firmware has...
View ArticleForum Post: RE: ADS1282EVM-PDK DSP NOT READY ... RETRYING
Hi Tonjun,Welcome to the TI E2E Forums!I see you found the wiki page regarding this issue. The ADS1262EVM-PDK works on Windows 7.Are you using the latest plugin found here:...
View ArticleForum Post: RE: lmp90100
Yes, that is the correct register addresses to readback conversion results.
View ArticleForum Post: Data acquistion and processing using CCS
Hi everyone,I'm going to order an 8 CH ADC along with the TSW1400 to capture data simultaneously, for further processing i'm thinking of using CCS on an AMM 335x module (TMDXEVM3358). So, Here's my...
View ArticleForum Post: RE: connecting external crystal to lmp90100
You can use an external crystal, or a single-ended clock input, or the internal oscillator. Refer to the section Internal/External CLK Selection in the LMP90100 datasheet for the configuration...
View ArticleClik here to view.
Forum Post: RE: Question about the ADC12D800RF Reference board:the...
Hello Tianyi,One more thing to try. In the WaveVision5 GUI, navigate to the "Registers" tab on the right side (shown below). Toggle the Clock Selection to "External Clock" then back to "Internal...
View Article