Forum Post: ADC12J400 Question
HiI was wondering if it would be possible to get the HLD code for this ADC. Also is possible to set up and automated run on this ADC (for example using a python code to test different input...
View ArticleForum Post: ADC board accesories
Hi everyone,I'm going to order the ADS5295 evm and TSW1400 evm, Here are some questions :* Does the ADS5295 evm already bring the ADC ads5295 onboard ?* What kind of cables do i have to use for the...
View ArticleForum Post: RE: LMP90100 ODR Range (using external clock)
Yes, you can operate at that sample rate, however you may not achieve specificationswhich are defined at the ~3.5MHz nominal frequency.
View ArticleForum Post: ADS7881EVM restricted dynamic range
Maybe somebody here can help me solve this problem.I'm running the evaluation module for the ads7881, but my usable input range is restricted to ~500-600mV of the 2.5V swing. If I input just a DC...
View ArticleForum Post: RE: TSW1400EVM Trigger Issue
Hi Thayne,There are occasional errors that I see, but 75% seems quite low. First, this is a CMOS input, so your signal levels seem ok. In HSDCPro, first turn off the trigger mode in the Data Capture...
View ArticleForum Post: RE: ADS1299EEG-FE Zip archive password
Hi Yohan, An email has been sent.Regards,
View ArticleForum Post: RE: ADS1299EEG-FE Zip archive password
Hi Bernardo, An email has been sent.Regards,
View ArticleForum Post: RE: Source code DSP TMS230 for the MMB0 with ADS1299 EEG FE
Hi Juan, Maruo, An email has been sent.Regards,
View ArticleForum Post: RE: ADS 1299 Input voltage
Hi Summer, A differential input of 0.8 V will not damage the device. Damage occurs when the absolute voltage on each input pin exceeds the supply voltages by 300 mV (AVSS - 0.3V or AVDD + 0.3V). The...
View ArticleClik here to view.
Forum Post: RE: Question about the ADC12D800RF Reference board:the...
Hello Luke, thank you for your help. I would provide you more information now: 1.At the start ,we use the clock on board, and we test the input differential clock of the ADC using a RS spectrum...
View ArticleForum Post: RE: TSW14J56 EVM
Jim,Hope you got back safe. I'm having good luck with getting things working, but the firmware examples would really help.For some reason DAC out A, C and D look fine, but B is noisy. They all look...
View ArticleForum Post: RE: About the use of DCLK2 of ADC08D1020
Hi,I need your help about some other questions.1.when the ADC operating in DES mode,how shoud i do to the unused analog input channel DI or DQ?In datasheet ,the unused channel shoud be connect to...
View ArticleForum Post: RE: Using LDC1000 for measuring load on a rod
I have sent you friend request.Kindly share the document after gets finalized as soon as possible.
View ArticleForum Post: DAC38J84EVM Alarms
I'm using a DAC38J84EVM with a TSW14J56EVM and their included software GUI. I get nice looking sine waves with various lane rates, clock speeds etc. But I always get "DAC PLL Out of Lock" and "SERDES...
View ArticleForum Post: Doubt on USB codec
Hi All,one of my customer wants to read the audio file from USB stick/SD card and wants to give it to audio amplifier and in turn they will control this IC thru I2C/SPI from Microcontroller. Do we have...
View ArticleForum Post: ADS1015 I2C reading technical problem
I have in my development system ADS1015 device which is sampling an analog signal with varying voltage levels.When I try to read the sampled data in the conversion register of the device over I2C bus I...
View ArticleForum Post: RE: Machine driver for TLV320AIC3100 codec
Hi All,Once i did some changes in my machine driver , i am able to play audio in my board.This one i can see in my console and by using log but not able to hear form HPLOUT and HPROUT pin.Once i probe...
View ArticleForum Post: RE: external clock adc12d1800rfrb not working
Hello GottardoWe have a ADC12d800RFRB, and it is also the newer version as yours. We meet the problem that no matter wether we use the on board clock or external clock. The led pattern is same as the...
View ArticleForum Post: RE: LDC1000 EVM GUI 1_0_4_1
Thank goodness I found this thread. I have been wasting a lot of time with GUI 1.0.4.1 and the latest firmware on two eval boards. One vanilla the other with an external wound coil. First one worked...
View Article