Forum Post: RE: Help me! I can not install USBStyx Driver !!!
Le -Please refer to http://e2e.ti.com/support/data_converters/precision_data_converters/f/73/p/336435/1173863.aspx#1173863 to see if this helps to resolve your problems.
View ArticleForum Post: RE: ADS1274-EVM cannot be connected
Double post -Please refer to http://e2e.ti.com/support/data_converters/precision_data_converters/f/73/p/228099/1172087.aspx#1172087
View ArticleForum Post: RE: DAC8560EVM USB Issue
Jon,You might try installing the DXP driver manually using the .inf or the .exe in the DXP installation. That is <installed directory>/DXP/drivers/dxp_driver/Let me know how that works out for you.
View ArticleForum Post: RE: FAN CONTROLLER
Howdy Eli,The AMC6821 EVM is currently only compatible with Windows XP Operating systems. The EVM uses an older interface board, the USBMODE EVM, which only operates with the earlier Windows XP...
View ArticleForum Post: RE: Reg MSC1210y5 program is frequently deleted.
Hi Ramesh,A mixed voltage system does not usually work well together. Most CMOS devices have ESD protection cells that act like a diode connection to the supply. A 5V device output will force current...
View ArticleForum Post: RE: LDC1000 evm linux driver
http://e2e.ti.com/support/data_converters/inductive-sensing/f/938/t/295036.aspx#Q18
View ArticleForum Post: RE: Interfacing TLV320AIC3254 Audio codec driver
Hi, Rajam,I hope someone in the community has some tips for you. We do not have experience with this devices and the OMAP4460.You may want to investigate approaching one of our Third Parties for help...
View ArticleForum Post: RE: LDC1000 EVM GUI 1_0_4_1
Hi Charles,I uninstalled and reinstalled a few times. I couldn't rollback, because the older driver had never been installed. Every time I reinstalled (directing windows to the 1.0.3.0 driver...
View ArticleForum Post: RE: Zeros as the output values from miniDSP aic3254
Do you use PPS with the EVM or are you loading the configuration into your own hardware design? If you insert a biquad or alaw encoder between the splitter and the I2S out and you have a valid input...
View ArticleForum Post: RE: Issues in interfacing ADS54RF63EVM and DAC34SH84EVM with...
Hi Kang, Thanks a lot for pointing out the example register files. I am trying to understand what each of those are, with reference to the DAC34SH84 datasheet. In order to generate my 270 MHz clock...
View ArticleForum Post: RE: Switching Gas Sensor Platform to Oxygen Mode (LMP91000)
Perhaps a better way to state my problem:I downloaded IAR embedded workbench and switched the settings to O2 mode (I think...) but when I try to download and debug the new firmware settings to the...
View ArticleForum Post: RE: using tvp5158 and dm6437 clock problem
I don't have an EVM either unfortunately.All I am able to confirm is that the OSC_OUT pin does oscillate as without any configuration. Given this fact I think that the OSC_OUT pin will oscillate as...
View ArticleForum Post: pcm4220 bandwidth : 0.4885*FS, not 0.4535*FS
Dear all,we are running the PCM4220 at FS=100kHz, classic response. A linear frequency sweep is injected in the analog inputs, the data are read and the FFT clearly shows that the -3dB frequency cutoff...
View ArticleForum Post: RE: ADS1255 wrong data appear after a random time
Hi Laurent,Glad to hear you're getting good data!Self-calibration will remove many of the ADC errors. System calibration will help remove the errors before the ADC.Changing the data rate and PGA should...
View ArticleForum Post: RE: Influence of amplitude setting in LDC1000
Let me add that knowing Rp value, as measured by LDC1000, and the setting for Vpp, you can calculate the current that goes into tank as <I> ≈ Vpp/2/sqrt(2)/Rp
View ArticleForum Post: RE: DAC6574 SDA line held low
I found the problem, I was writing a 'Read' bit at the end of the address byte (LSB), and it should have been a 'Write' bit.0b10011001 and it should be 0b10011000I hope this helps someone in a similar...
View ArticleForum Post: RE: TVP7002 Fuzzy text
All I can suggest at this point is to display alternating black/white, single pixel thick vertical lines then look at the input pins of the TVP7002 with an oscilloscope to make sure that you are not...
View ArticleForum Post: ADS7950 Series ADC Clock Source
I am considering using the ADS7953 in a design. From looking at the datasheet, SCLK is depicted as a free-running clock. However, the microcontroller I am using does NOT have SCLK as a free-running...
View ArticleForum Post: RE: ADS131E08 never responds via DOUT
Thank you for the reply Greg,Clock is SCLK, The SCLK was running at 62.5 KHz. After finding equation one, i see that it requires ~5.2 MHz (32kSPS, and 16 bit resolution is default) on the SCLK line. I...
View ArticleForum Post: RE: Issues in interfacing ADS54RF63EVM and DAC34SH84EVM with...
Hi,the loop filter will impact the shape of the phase noise. The clocking forum support can help you further on the CDCE62005 configuration.-Kang
View Article