Forum Post: RE: Off topic: Basic question about strain gauge
Hi Aamir,You may find this NIU lab information valuable in understanding the relationship.http://www.kostic.niu.edu/strain_gages.htmlBest regards,Bob B
View ArticleForum Post: RE: LMP91300 samples
Hi Imre,I'm currently talking with the planner about resolving the digikey inventory problem. However, if you like to give us an address we can send 1 or 2 engineering units from the factory in the...
View ArticleForum Post: RE: Question on Verified Design Hardware – Compensated...
Hi Orlando,The current source mismatch is not random, and they will track together nicely over temperature. When using the 3-wire RTD, you can remove the mismatch by taking a measurment, swap the...
View ArticleForum Post: RE: ADC128D818 I2C ACK problem
Hi,Some possibilities to check:Are there other pull up resistors on the SDA and SCL lines for other devices? These would be in parallel with the 2.2k resistors and may make the total parallel...
View ArticleForum Post: RE: How to store DAC3XJ8X GUI v1.0 configuration
It looks like it is only items on the "Quick Start" tab that are not saved. I can use the "Save Config" and "Load Config" on the "Low Level View" tab to save items on other tabs.The "Quick Start" tab...
View ArticleForum Post: ADS5281 behavior on clock loss
Hello,I would like to ask what is the expected behavior of the ADS5281 after the driving clock has been suspended for substantial time (miliseconds - seconds)?I have order of 400 ADS5281, ~10 mounted...
View ArticleClik here to view.
Forum Post: DAC38J4 LMF values
I'm a bit confused by Tables 9 and 10 in the March 2014 DAC38J4 datasheet. For example, in the LMF=442 column, F=2 means there should be 2 octets per frame. It seems to show 4 octets. Same issue with...
View ArticleForum Post: RE: Measure thickness
A lot of different devices are available like vernier caliper and screw gauge. These are such devices which provide you more accurate results.
View ArticleForum Post: RE: Strain gauge measurement circuit ads1248
I will use bridge circuit as might be I have to place dummy gauge for temperature compensation.One problem: I have placed filter R6,R7,C1,c2 & C3 for filter. Since my circuit is battery powered so...
View ArticleClik here to view.
Forum Post: Multiple(3) Ads1248 on same SPI line
I have to connect 3 ADS1248 on same SPI bus. I have attached a schematic.Each ADS1248 contain 3 strain gauge connections.Since my circuit is battery operated so I have to keep power minimum.I have kept...
View ArticleForum Post: RE: LMP91300 samples
Hi Imre,I will get the engineering samples out on Monday.Thanks,Tarig
View ArticleForum Post: RE: PCM2704C volume control
Dear SirThanks for your reply quickly OK!! I will check the elaborate system structure and feedback the information on MondayOur OS : Windows XPDriver : PCM2704C TI website driver If the 3pcs of...
View ArticleForum Post: DS90Ux92x FPD-Link III Devices
Hi,Is it possible to have multiple Desirializers for one Serializer or a way of repeating the information to multiple locations.ThanksDanny
View ArticleForum Post: RE: ADS5463 Timing
Hi,I am using Virtex 6 ML605 board to latch the digital output data coming from ADS54RF63EVM. It would be really helpful if I could get in touch with fellow users with respect to this issue. I am...
View ArticleForum Post: RE: Password required for...
Hi,Please send me password the .zipMy email id is uriberuben89@gmail.comThanks
View ArticleForum Post: RE: DAC37J84 datasheet
Matt-san,Thanks for your reply.When is the revised datasheet scheduled to release?Thanks in advance.Best regards,Toshi
View ArticleForum Post: VSP8133 CCD AFE
Dear SupprtI have a follwing issue.Please give me a advice.[Issue]My customer is using VSP8133.Rarely, it may become a frame brighter than other frames.[My reasoning]When VSP8133 is resived a noise...
View ArticleForum Post: RE: ADS1293EVM 5 lead application
Hi Alexandros,For safety and liability reasons we only recommend that the EVM is used with a simulator and we cannot make any recommendations to you for connecting the EVM to yourself or another...
View ArticleForum Post: TVP5158: 4Ch Line interleave mode clocking query
Hello,We are using TVP5158 and interfacing it with Davinci processor.Problem statement: - We are using TVP5158 in 4-Ch line interleaved mode, and it is mentioned in datasheet, that output clock OCLK_P...
View ArticleForum Post: RE: TLV320AIC3110 circuit suggestions
Hi,Could you please suggest your views on the same, Iam waiting for suggestions on these Audio Codec.RegardsAnil
View Article