Forum Post: RE: TLV320AIC3110 Codec I2S Signals and EMI Filters
HiI Updated my thread, could you please share your thoughts on the same.RegardsAnil
View ArticleForum Post: RE: TLV320AIC3268 EVM support software7driver
Hello Don,I have entered the registration for the purepath console tool to download the software tool, thanks!The project itself is not a business relevant play book project. It's rather an evaluation...
View ArticleForum Post: RE: ADS1218 - ssi clock
HI Bob,I am indeed using GPIO pin for Slave Assert but i m also using End of Transmission Interrupt which provokes when data is shifted out from the chip . Anyways so i was looking at the timing...
View ArticleForum Post: RE: ADS130E08 Daisy-chain
The DAISY_IN bit is set to 0 by default on the ADS130E08, so it should work only in Daisy Chain mode.
View ArticleForum Post: RE: ADS131E08 OpAmp
Gerardo -As long as you don't violate the reference specs on startup/power-up (due to power transients), there isn't any reason that you can't do this.However, the reference directly affects the...
View ArticleForum Post: RE: ADS1293 Evaluation Board Firmware Source Code
Please check on this in the BLE CC254x forum. Thanks.
View ArticleForum Post: RE: TLV320AIC3110 Codec I2S Signals and EMI Filters
Please connect HPVDD to +3.3V and HPVSS to GND. HPVDD also powers internal blocks like the PLL so you must not leave it disconnected.Please pull up VOL/MICDET with a 10k resistor to IOVDD.Pull down...
View ArticleForum Post: RE: ADS5281 behavior on clock loss
Hi Richard,thanks. That would be highly appreciated.- Jiri
View ArticleForum Post: RE: ADS1248 reading digital inputs problem
Hi Alexandra,If you issue the SDATAC command, there is no need to issue a delay between commands. The stretched clock and the 25 clocks instead of 24 will cause you many issues. The SPI interface for...
View ArticleForum Post: RE: Initial demo file for using port A of FPGA with TSW1265 EVM?
Richard,Thanks for clarification. We are considering the use of FMC bridge adapter with HSMC to FMC converter. Hopefully that will help with getting access to more LVDS routings.Appreciate detailed...
View ArticleForum Post: RE: TLV320DAC3100 lineout driver loading
Thanks D. Hartl, any chance you could point me to a sample schematics/application demonstrating how to wire the output stage for driving in lineout mode ?
View ArticleForum Post: ADS1242 Crystal start-up
Hello,We are experiencing some problems with crystals stopping after a while when used with an ADS1242 ADC. In some cases, failure can occur after over a year of continuous operation whereas on other...
View ArticleForum Post: RE: How to store DAC3XJ8X GUI v1.0 configuration
Matt,That's very helpful. I see after I hit button 1 in Quick Start, the values now match.You've sort of hit on my next question. I take it the "Step 4 - Program EVM" buttons in the Quick Start are...
View ArticleForum Post: Obtaining 128 kHz BCLK on TLV320AIC3105 in DSP mode for 16 bit...
HaiAm working on TLV320AIC3105 codec and am able to set the WCLK to 8kHz. I want the data length to be 16 bit for the ADC and DAC operation so the BCLK generated will be around 256kHz ,well this BCLK...
View ArticleForum Post: LDC1000 EVM Clearance
HiWEBENCH showed that this device could detect metal among 1 to 7 mm.(10um resolution)But, If the bottom has metal, the value will influenced.Do you have distance value of clearance of EVM....
View ArticleForum Post: RE: 230Vac sensing using AMC1100
Hello Jose,I'm in need of RMS voltage of my input AC supply (230Vac, 50Hz). In my software, I can read my ADC for only 250ms once and adjust a gain parameter accordingly. I can do only very limited...
View ArticleClik here to view.
Forum Post: LDC1000 GUI Disconnect
HiWhen I change value of configration, GUI can not connect the EVM.When the configuration of GUI was changed, the EVM became impossible to connect to a COM port. I tried to reinstall GUI and restart...
View Article