Forum Post: RE: DAC5687 Configuration for different IF signal path
KangThank you for reviewing my issue.-Jin
View ArticleForum Post: RE: Password required for...
Password effective. Thank your help.Best Regards,Andy
View ArticleForum Post: ADS4146 - The specification of output voltage of CLKOUT in the...
Hello,My customer have a question about ADS4146.[Q]Is CLKOUT 1.8V CMOS Interface in the CMOS mode?Can they refer to "DIGITAL OUTPUTS (CMOS INTERFACE : D0 TO D13, OVR_SDOUT)" (datasheet P.8) for the...
View ArticleClik here to view.
Forum Post: How to store DAC3XJ8X GUI v1.0 configuration
I'm using the DAC3XJ8X GUI v1.0 to setup a DAC38J84EVM board. There are many parameters that need to be setup but I don't see any way to save them. There must be a way.A way to increase the font size...
View ArticleForum Post: RE: msp-expf5436A sample music with ADC
Hi, Arkady,As far as I know, we don't have too much info here. You might try posting in the MSP430 forum to see if any of the Community members there can share their experiences with you.-d2
View ArticleForum Post: RE: PCM2704C volume control
Hi, Kai,I've asked my colleague to work with you on this next week.-d2
View ArticleForum Post: RE: PCM1808 + DS90UA101(Serializer)
Hi, K.I.,Unfortunately, I don't think anyone in this forum is knowledgeable about the serializer/deserializer that you are using.Please allow me to move your post to our automotive forum. I hope...
View ArticleForum Post: RE: LM49352 Linux driver for OMAPl 138/AM1808
Hi, Sangly,You can see if you can find an Open Source Linux driver for this device, otherwise, you are going to have to develop your own.-d2
View ArticleForum Post: RE: TLV320AIC3268 EVM support software7driver
Hi, Albert,The EVM is stand-alone. You don't need to use other stuff.The s/w is available from our registration-download site. You can go to: http://www.ti.com/tool/PurePathConsoleCan you share Play...
View ArticleForum Post: Password ADS1299 Firmware
GreetingsPlease i need the password to open the firmware.My email: jsalas@cinvestav.mx
View ArticleClik here to view.
Forum Post: RE: ADS1299 and MSP430F5529 issue reading ID register
So i managed to get my hands on a Logic Analyzer, i was toggling CS on this program, here are the screenshots:0 = CLK1 = DIN on ADS12992 = DOU on ADS12993 = CSThis is are the two behaviors i get from...
View ArticleForum Post: RE: Problems with SPI protocol between my MCU and LDC1000.
Glad you got it working!Let me know how we can further assist.Thanks,
View ArticleForum Post: RE: DAC 7568
For a code review, post to the C28xx forum. I am not familiar with their peripherals to view your code.If you probe the bus with an oscilloscope and post your captures I'd be happy to look at it.
View ArticleForum Post: RE: ADS1248 stops converting
Hi Keiichi,If you write to any of the first 4 registers, the conversion cycle will restart. If a command is issued, such as SELFOCAL, the conversion cycle will take extra conversion time beyond the...
View ArticleForum Post: RE: PCM2704C volume control
Please elaborate what (and how) you are exactly doing.Do you use UI controls from Windows or are you actually writing your own software to control the volume of each PCM2704?The PCM2704's, if attached...
View ArticleForum Post: RE: ADS1218 - ssi clock
Hi Shubham,I think you are missing what is happening in the communication. Please look at the timing diagram of the datasheet. You must communicate in 8-bit (byte) transfers and not 16 or 32-bit...
View ArticleForum Post: HSMC-TSW1266EVM bridge
Hi,I am using following wide-band development Kit for my system level design,http://www.ti.com/ww/en/Altera/pg_dc.html I want to replace dual-band TSW1265 receiver with TSW1266 wideband receiver. Do we...
View ArticleForum Post: Initial demo file for using port A of FPGA with TSW1265 EVM?
Hi,I am using following development kit for my system level design.http://www.ti.com/ww/en/Altera/pg_dc.htmlCan ti provide any initial demo FPGA programming file for using port A of FPGA to receive...
View ArticleForum Post: RE: Strain gauge measurement circuit ads1248
Hi Aamir,You could use the circuit you provided. You could even simplify the measurement and make the strain guage connections similar to an RTD measurement using current excitation (by removing R1,...
View ArticleForum Post: RE: What property changes when Insulating media is introduced...
Hello Naveen,yes, it seems like you are seeing a capacitive effect. The oscillation frequency of the tank that the LDC1000 measures is determined by f=1/(2*pi*sqrt(LC)). Increasing the LC tank...
View Article