Forum Post: RE: pcb coil
The highest risk with such a coil is self-capacitance, that can potentially bring the self-resonant frequency too low, potentially outside of the LDC1000 range.Low resonant frequency also means that...
View ArticleForum Post: RE: Measuring angle using LDC1000
You are most welcomeYou can compensate non-linear response in post-processing, using look-up table, for example
View ArticleForum Post: RE: TVP5150AM1 Data stream and I2C instructions
I didn't know an external clock was necessary. But i see it on the datasheet now. I guess I can just get a crystal for it. But there is a clock output? Is this pin only used to sync each byte that...
View ArticleForum Post: ads42lb49 syncinp input in QDR mode
Hello,I am currently working on interface for ads42lb49 ADC (Xilinx fpga), and I am having problem with understanding SYNCIN pin. Configuration of adc:- QDR mode- 200 MHz clk into ADC (200 MSPS), no...
View ArticleForum Post: RE: COncentration of ions
Hello,It's a feasible application, for sure.Do you know expected conductivity of the solution?
View ArticleForum Post: RE: TSW1200EVM FPGA Source Code Request
Hi,I have been out of office so I apologize for the delay.if you just need to reprogram the eeprom, attached is a zip file of the batch file and folder that we use to program the eeprom when the...
View ArticleClik here to view.
Forum Post: [tvp7002] Is it possible to remove almost SAV and EAV?
With TVP7002, customer converts input video signal from YPbPr (component) to digital video.For about the video signal, is it possible to remove all (almost) SAV and EAV, and get only Active Pixel and...
View ArticleForum Post: RE: TSW1400EVM (Rev D) JESD204B connector
Hi Dave,Thanks for reporting back with the outcome of your investigation. It might be useful for others (like myself :).Cheers,Steve Ryan
View ArticleForum Post: RE: Connecting ADS42LB69EVM and ADS42JB69EVM 250Msps 16-bit ADC...
John,The ZYNQ on the Zedboard does not have any transceivers.
View ArticleForum Post: RE: ADS6445EVM - BOM/Schematic mismatch
Good evening, Richard,The transformer listed on the schematic and the transformer actually populated are not the same thing; the transformer that is actually populated for the clock input is the same...
View ArticleForum Post: RE: ADS1248 7 PT1000 connections
Hi Wurker,Meanwhile any other help from forum members......RegardsAamir
View ArticleForum Post: RE: TSW1400 matlab code！
HI ken,Can I use TSW1400_5F00_Matlab_5F00_Code.zip with 64-bit OS? Regards, Fathima
View ArticleForum Post: RE: LM49352 sometime loudspeaker gets hot.
Hi Don,thanks for your quick reply.Are there any information about the state machine of LM49352?In the available specification I cannot find such information.Maybe could you tell me a contact person...
View ArticleForum Post: RE: Usage LDC1000EVM in custom application
Hi,LDC1000 use counter to measure frequency, if the data rate is high, we can only get less counts in every sample, you can use large inductance and high Q coil, then we may get more counts. Or you can...
View ArticleForum Post: RE: LDC proximity reading confusion
Could you reduce RpMAX setting by 1 or 2 codes (1-2 steps up in resistance) and see if it helps?
View ArticleForum Post: RE: LDC1000 newbie
Hi,Yes, ODR register is just the indutance data, you can use large inductance and high Q coil, then we may get more counts. Or you can use moving average filter after you get the data.Thank you!
View ArticleForum Post: RE: ads1248 RTD read problem in temperature test
Dear Yavuz,okay, then it seems like we need to dig deeper to find the root cause for this issue. However currently I do not know where to start. Can you describe exactly how the output code changes or...
View ArticleForum Post: RE: LDC1000 to sense feed in auger
Hi,First, LDC1000 can sensing through PVC. It can`t detect feed directly, but we can use something indicate the feed level, such as metal ditance change, or spring change, then we can use LDC1000 to...
View ArticleForum Post: RE: ADS8361, DAC8554 to C6713 DSK interface code
Hi Burkhard,Figures 1 and 2 look a little strange - like you have some aliasing going on with your scope. If figure 3 is correct and your clock is ~120ns (8.33MHz), then you don't have enough clocks...
View Article