Forum Post: RE: AMC1210 Out-Of-Whack Readings and Data Unavailable
Hi Rolf,Is there anyway you can connect up the ACK pin as an interrupt? That would be the best way to go. Is it possible to speed up your reads so that they are at the data rate/2 and synchronized to...
View ArticleForum Post: Using the DAC37J82 as a quadrature DDS ?
I would like to explore using the DAC37J82 as a quadrature DDS (and ignore its modulated waveform capability). It has a 48bit NCO and appears to have suitable noise levels. I would seem that we need...
View ArticleClik here to view.
Forum Post: RE: ADS6445EVM - BOM/Schematic mismatch
Your recollection of the clock input is correct: (The actual ADC channel inputs have two back-to-back transformers to achieve better frequency response, but the clock input is the single transformer...
View ArticleForum Post: RE: capacitive load stability of AMC7812 DAC part
Hi Matt Thank you for your reply. So I want to know when I could get the latest datasheet? Best Regards,David
View ArticleClik here to view.
Forum Post: [TVP7002] question about reset timing
From data sheet of TVP7002, it explains about RESET timing as below."RESETB may be low during power up, but must remain low for at least 1us ..."It sees that "Figure 7" has one thing wrong with "1us"...
View ArticleForum Post: RE: ADS8361, DAC8554 to C6713 DSK interface code
Hi Burkhard,Without RD+CONVST and CLOCK inputs going to the ADS8361, it won't be doing what its designed to do - there will be no conversions and the data you see in Figure 2 may be correct from that...
View ArticleForum Post: RE: TLV320AIC3104 Line Out -- Short Circuit Protected?
Hi, Jim,I've asked my colleague to comment on your questions.-d2
View ArticleForum Post: LDC1000 to sense feed in auger
I'm looking to use the LDC1000 to sense the presence of feed (corn based) inside of an auger. The feed could be pellets or finely ground up like flour and anything in-between. The LDC1000 sensor coil...
View ArticleForum Post: RE: LM49350 Driver for WinCE & Android
Hi Don,Can we use this audio codec for WinCE & Android with customized driver?Regards,Pankti Shah
View ArticleForum Post: TLC5620 JUNCTION TEMPERATURE
HiWhat is the manufacturer's max junction temperature or case temperature limit of the TLC5620C?I can't search on datasheet.Pls help~
View ArticleForum Post: RE: AIC3204 DAC problem
Hi John,w 30 02 00 was disabling the AVDD LDO power and when i used to select this configuration AVDD pin wasn't showing me the set voltage, so i selected w 30 02 01 for setting the 'AVDD LDO powered...
View ArticleForum Post: RE: ads1248 RTD read problem in temperature test
Dear Yavuz,your schematic looks okay from what I can see.As I said we usually recommend some differential and common-mode RC filter on the inputs. But you would then probably not be able to measure all...
View ArticleForum Post: RE: TSW1400EVM (Rev D) JESD204B connector
Ken,Do you know if the DAC3XJ8EVM is compatible with the FMC connectors on the Xilinx ZC706 board? There is no pinout in the "User's Guide" for me to check it myself.
View ArticleForum Post: IOVDD and DVDD in ADS1278 can tie together to 3.3V?
From ADS1278 datasheet"The IOVDD and DVDD power supplies available directly, bypassing the internal digital filter.can be tied together if desired (+1.8V)."But in absolute maximun ratingDVDD, IOVDD to...
View ArticleForum Post: RE: capacitive load stability of AMC7812 DAC part
Hi David,This datasheet edit is queued in our system. Most of our datasheets are being updated to a new template format, so I'm unsure when this change will be reflected, but rest assure that it is...
View ArticleForum Post: RE: TLV320AIC3104 Line Out -- Short Circuit Protected?
Thanks for the quick reply. I will use 1K in series with each line output.
View ArticleForum Post: RE: LMP91300 - supported by SPIO-4?
Hello,Could you email me at mike.stout@ti.com so that I can get in contact with you?Thanks,Mike
View ArticleForum Post: RE: Board house that MFG's with Stainless STS416
Hi Jeff,The target you choose is a particular metal target that your coil will sense, and not the metal of the coil itself. The coil is typically 1oz copper PCB trace. You would have to source your...
View ArticleForum Post: RE: AMC1210 Out-Of-Whack Readings and Data Unavailable
Hi Rolf,By speeding up your reads, I was thinking that perhaps you could get to your data rate (39.6k) over 2, or ~19.8k. Perhaps slower would be an option for you as well, down around 13.2k. You...
View ArticleForum Post: RE: Maximum output data rate
Hi,Unfortunately not possible with the current IC. I am so sorry.Sunny.
View Article