Forum Post: RE: No signal from the DOUT pin in ADS1299 EEG-FE
Hi Xinling, Yes, the default mode for reading back data is RDATAC. The way you describe reading the data should be fine. The only concern with an SCLK that is too slow (with too much delay between...
View ArticleForum Post: Measuring dielectric permittivity
I am interested in measuring the presence (or absence) of a material whose permeability (Mu) isn't much different to free space but the permittivity (epsilon) is. Use water as an example;Mu =...
View ArticleForum Post: RE: Interfacing of Insulogix Hydrogen Monitor with 7 Segment LED...
Hi Bob B,Thank you for your reply. The information which yoy gave is really helpful. I wanted to know one more thing. 1) How can I program the micro controller for the different values of the current (...
View ArticleForum Post: ADS1292R respiration modulation internal topology and Output...
Dear professionals,Could you help to understand the output stage of the respiration modulation block, can one side be tied to ground?What is the output impedance of the RLD output buffer? Output...
View ArticleForum Post: ADS1292 - drivers for windows 8
Hello, I have a question about compatibility ADS1x9x evaluation kit, with windows8, resp. windows 8.1, are there any drivers for w8? i couldn´t find it and it seems the old one doesnt work for me.If...
View ArticleForum Post: RED LED stuck on
Hi,I just received my LDC1000 EVM, when I plug it into the USB connector the red LED is always on? It also does not work as expected. Can you tell me what logical next steps in debug would be?
View ArticleForum Post: RE: Low cost ADC
You, can search at product page and then check prices at digikey or mouser.-kel
View ArticleForum Post: RE: ADS1234 Data rate problem
Hello Sir,Good Morning. Thanks for support.I done everything as per your suggestion, but i can't got low in DRDY pin.I tell you one thing,, can I test ADS1234 without microcontroller... not require...
View ArticleForum Post: RE: TWL6040
Was this question answered?Our customer is also requesting the full data sheet of the TWL6040. How can I obtain it?Thanks,Rani
View ArticleForum Post: [WaveVision 5, Win 7, 32-bit] - ADC08D1520 RB Test Pattern Output
Dear all,I am facing a problem in which I hope someone can help me out.I have used the matlab code supplied by other forum members to communicate with ADC08D1520RB. The code needed some modifications...
View ArticleForum Post: RE: sensor frequency
To select the correct capacitor for the system it is necessary to choose a sensor frequency. I want to know what the advantages of the different sensor frequencies are? What are the criteria to choose...
View ArticleForum Post: RE: TI AIC23 audio codec
Ok, looks like I didn't have the MCLK at 12Mhz. It appears to work well now although I am getting a decent amount of noise.If anyone else is working with a NIOS II with an AD/DA daughter card I am...
View ArticleForum Post: High Speed Digital Interface Board Version 4.4 (ACTIVE)...
Hi, I have a legacy High Speed Digital Interface Board Version 4.4(ACTIVE) WAVEVSN-BRD-4.4 which I would like to keep using but not sure if it is any good for the newer or older 10-100 Msps ADS and DAC...
View ArticleForum Post: RE: Interfacing of Insulogix Hydrogen Monitor with 7 Segment LED...
Hi Sabyasachi,The LaunchPad products are outside my area of support (precision data converters), so you will need to contact the appropriate forum.Best regards,Bob B
View ArticleForum Post: RE: ADS1292 - drivers for windows 8
The current software does not support Windows8. It should support up to Windows 7.
View ArticleForum Post: RE: ADS1248 SCHEMATIC FOR 2-WIRE PT1000 RTD
Hi Paulo,That configuration looks to be ok, but you may find that different component values may be desired for best ratiometric matching. Also, if you are to use 3.3V for the analog supply, you must...
View ArticleForum Post: RE: sensor frequency
Hello,There are 3 parameters relate to Sensor frequency:1, Data rate, high frequency will get a high data rate;2, Q, high frequency will get a high Q of LC, then the noise will be better;3, Tempco,...
View ArticleForum Post: RE: Measuring dielectric permittivity
Hello,Yes, you can use LDC1000 to measure Capacitance, but can you tell me the capacitance of your sensor? Or the capacitance change range?Thank you!
View ArticleForum Post: Adding additional gain and attenuation adjustment to the transmit...
Hello,I want to add additional gain and attenuation adjustment to the transmit path and trying to follow following options suggested in user guide:For TX Path #1• Remove C258 and R165• Install 0Ω to...
View Article