Forum Post: RE: Data generation TSW3100(1400) and two TSW3085EVM
Hello,The signals besides DATACLK and FRAME look fine. For the DAC3482, the LVDS receivers on the LVDS bus have 100ohm on-chip termination. By sharing the same DATACLK or FRAME signal with two DAC3482...
View ArticleForum Post: RE: DAC34SH84 DC-Offset Problem
Hello,The DAC34SH84's DC offset feature can help adjust the DC offset introduced in the signal chain (both DAC and analog quadrature modulator). Often, DC offset of a few uV to mV range is needed to...
View ArticleForum Post: RE: DAC5689 Real IF inteface - Independant & Differenct frequency...
Hi,The input bandwidth of the DAC is limited by the FIR1 (2x interpolator) low pass filter limit. To generate 75MHz, you will need data rate higher than 100MSPS. I suggest that you use 200MSPS input...
View ArticleClik here to view.
Forum Post: RE: Internal Clock for ADC12D1800RB
Hi, It depends which version you have. There have been several iterations of the eval board which made various changes and improvements. There are two quick methods to determine which you have.You can...
View ArticleForum Post: RE: New 1292 Design software questions
Hi,Could please send me the password for the ADS1x9x_ECG_RECORDER_USB_DLL.zip ?my email id is mariappan.n@hardcube.in.Also do you have any idea about the data packet structure which received from the...
View ArticleForum Post: RE: TLV320AIC3104 I2C lines held at low
Hello,Issue is sorted out..there was issue with the CODEC Reset which has a glitch and not getting driven accurately as per the datasheet..YKFS
View ArticleClik here to view.
Forum Post: RE: Internal Clock for ADC12D1800RB
Hi, I am using the ADC12D1800RB2 board.On the ADC 1xDxxxx(RF)RB User's Guide, it says that you can control the clock on WaveVision 5I'm really confuse with it. So, which one is the correct one?Also,...
View ArticleForum Post: RE: ADS 1298 PC Software
You should receive an email shortly with the requested information
View ArticleForum Post: RE: LDC1000 Drive-by-wire application
Hi Jamie,The inductive sensing group mentioned that drive-by-wire can include many applications of position and motion sensing such as pedal rotation sensing, steering wheel rotation, wheel speed,...
View ArticleForum Post: RE: Noise issue in a voltage measurement APP with the ADS1247
Hi Jason,This depends on the actual implementation of the digital filter and the precise time of a change. It may appear as an average, but the degree of change and the time the change occurs within...
View ArticleForum Post: RE: ADS1248 SCHEMATIC FOR 2-WIRE PT1000 RTD
Hi Paolo,This is close to what I think it should be, however I would move the common mode caps (the ones to ground on the analog inputs) to the other side of the input resistors so that there will be...
View ArticleForum Post: RE: ADC108S022
hi Ryuji,This power solution looks good to me. Just make sure VD does not power up before VA.Sincerely, tom
View ArticleForum Post: RE: AIC3204 simultaneous acquisition of stereo channel
Hi, Nitin,Unfortunately, we are not familiar with the Spectrum Digital boards. Have you tried asking them for help?Actually, I can answer this - AIC3204 can only ADC two channels at a time.-d2
View ArticleForum Post: RE: TAS 5760LD after power on : first write I2C command will not...
Hi, Paul,Very interesting! I have asked my colleague to try and duplicate this here.-d2
View ArticleForum Post: RE: concerns: ADC0XD1520RB could not be detected by wavevision 5
Hi BridgetCan you confirm which EVM you have? Is it the http://www.ti.com/tool/adc07d1520rb or the http://www.ti.com/tool/adc08d1520rb?Can you capture a screen shot (Alt-Print Scr) of any error...
View ArticleForum Post: RE: Sensor design information
Think of it as a very good conductor of the magnetic field, similar to a metal and current.The field will go in the least resistive path, i.e. through the core. Thus one can direct the field to the...
View ArticleForum Post: RE: confirm ADC chips embedded on ADC0XD1520RB could not be...
Hi BridgetI hope the information in my earlier post helps resolve the startup issue with the board. Regarding your other questions:The /ECE jumper should be connected in Position 2, nearest to the...
View ArticleForum Post: RE: TLV320aic3254 Mixer/MAR-MAL/MicPGA confusion.
1: MAL and MAR are acronyms for Mixer Amplifier Left and Mixer Amplifier Right and are different from the MicPGA. There are no documented registers that control the MAL/MAR input routing. They are...
View ArticleForum Post: RE: Human body - any guideline?
Could you please elaborate, what you are trying to do?
View Article