Forum Post: RE: Human body - any guideline?
We design music keyboard, and we are looking for a "bare hand" controller HID.Measuring hand moves over 10 cm with 1 mm resolution is about the minimum goal for us.Measuring 20 cm with 1 mm resolution...
View ArticleForum Post: RE: No signal from the DOUT pin in ADS1299 EEG-FE
Hi, Ryan, Thank you so much for your reply.I am using a SCLK boud rate of 480.5kHz and the default data rate of ADS1299 EEG-FE is 250 SPS, is the SCLK too slow?JP21,JP22,JP23 are all connected by 1-2...
View ArticleForum Post: RE: RED LED stuck on
Hi Jeff,Are you making sure that the coil is left untouched while the LEDs flash?Thanks,
View ArticleForum Post: RE: NTSC coder tvp5150am1
Please review the datasheet available here...http://www.ti.com/product/tvp5150am1In particular, look at the application circuit example in section 6.The device will need configuring though I2C to...
View ArticleForum Post: RE: ADS 1148 channel switching problem
Hi Primoz,The conversion will start as soon as the digital filter is reset and this takes place as soon as the MUX0 register has been written (relative to the falling edge of the last SCLK of the WREG...
View ArticleForum Post: RE: LDC1000 application question
Hello,The depth of the opening is given as 8mm in pdf, while you indicate that it is 10mm?Regarding the edges - are they well-defined, i.e. are they the same of shape/profile for all openings?If yes, I...
View ArticleForum Post: RE: EVM for angular position sensing
Hello Robert,There is no special EVM for this type of application at the moment.The resolution will vary depending on the particular implementation.In certain applications we are targeting achieving...
View ArticleForum Post: RE: Measurement of Rp
It is always possible and in fact the circuit already contained an inductor which was 30% of the overall inductance value that I quoted to you. I did not wish to complicate the question by including...
View ArticleForum Post: RE: DAC5689 Real IF inteface - Independant & Differenct frequency...
HelloThank you for your anwer.It is a helpful guide for me.Regards
View ArticleForum Post: RE: Can anyone send me a TLV320AIC3100EVM-U ?
Dear DonThank you for your reply.I have already confirmed TIJ sales and marketing, but they don't have.They suggested to use TLV320AIC3120EVM, it has the same analog performance.I will confirm the...
View ArticleForum Post: RE: DAC34SH84 DC-Offset Problem
DearMr. Meenakshi As you mentioned dc offsetappear at the local frequency. I agree with you. When I use an external mixer,your below comments are a wonderful support. But now I want to know thatcoarse...
View ArticleForum Post: RE: Searching for linux device driver for TLV320ADC3101
I read the post before, but I couldn't find a firmware for ADC3101.Now, I could find it in the wiki page suggested in the post.Thank you!
View ArticleForum Post: RE: PCM1804 input modeling questions
Don,Thanks for the help on this. The project is called Mako, and is a new marine chartplotter. They are using the PCM1804 in the sonar receive chain, downmixing the signal from the transducer into...
View ArticleForum Post: RE: TSW 1400EVM software for win 32 bit
Hi Taeyeop,Can you try with the XP version instead? This is 32 bits and it is more likely to work on your computer when you run in compatibility mode. The XP version is in the same location as the win7...
View ArticleClik here to view.
Forum Post: TLV320ADC3101, cannot see signal in GUI
Hi.I've been doing something with tlv320adc3101evm-k.Firstly, I wanted to see signal input/output at given GUI, but I cannot see it.I could connect EVM to computer, write program to EEPROM, and change...
View ArticleForum Post: RE: PCM2906C audio problem
Hi Don,Thank you for the quick reply.Yes, that's strange. As for the ground loop, I've isolated the whole pcb, by removing the source and replacing it through a 470 ohm resistor. The recordings are...
View ArticleForum Post: RE: TVP5150AM1 VITC slicing errors
Craig,Thanks for your reply. I've worked for hours trying to solve this issue without luck. Exchanging the NTSC and PAL in the config RAM helped a lot, but I still experience flipping bits in VITC...
View ArticleClik here to view.
Forum Post: Read problem of ADS7830
Hi,AllPlease let me ask you a question about ADS7830 because I was asked it by my customer.When they read a sampling value without wait time as following upper diagram,read value is always higher than...
View ArticleForum Post: RE: EVM for angular position sensing
Thanks Evgeny, that answered my question.
View ArticleForum Post: RE: Source code DSP TMS230 for the MMB0 with ADS1299 EEG FE
You should receive an email shortly containing the requested information
View Article