Forum Post: RE: DAC5689 t_align
Kobayashi-san,Since there are three forum posts regarding the same application for end customer, we will discuss this topic on the following forum...
View ArticleForum Post: RE: the problem of using DAC3484
Chunhao,When the DATACLK_gone alarm or FIFO collision alarm occurs, there are two possible errors:1. DATACLK/DACCLK ratio does not match the interpolation setting.2. DATACLK becomes interrupted in the...
View ArticleForum Post: RE: Problem with DAC348x GUI
Hi, This is due to Windows 7 font change while the Labview software is compiled in Win XP. This will be fixed on the next version of the software.-Kang
View ArticleForum Post: DS1248 EVM and SPI problem
Hello,I am using DS 1248 EVM board and trying to receive some data through SPI. I am using PIC18f97j94 controller as master.I am writing following sequence to receive at least some data from the DS...
View ArticleForum Post: RE: ADC14C080 / Temperature dependence of tOD
Hi,With an eval board, I used freeze spray to cool an EVM down below -40C and a heat gun to go above 85C. During the experiment, I saw the input clock to output data (tOD) decrease by 200ps @cold and...
View ArticleForum Post: RE: ADC14C080 / Output sate at power down mode
Hi,The output data and clock are Hi-Z when the device in is power-down modeRegards, Josh
View ArticleForum Post: RE: PCM1870A-The Max clk can be supply in BCK pin in slave mode
Hi Itamar,Just wanted to update you that SPI is write only in this device.Regards,~John
View ArticleForum Post: RE: TLV320AIC3256 Oversampling and decimation calculations
You are correct that the ADC_MOD_CLOCK is what drives the digital microphone clock. Your basic clock setup looks correct.What are your power supplies? Please make sure that your clocks don't violate...
View ArticleForum Post: Linear indutive transducer
Hi,With LDC1000 I can measure a inductive position sensor (one coil with two wires that change inductance with position) between 7mH and 25mH? After, I need a acquisition frequency of 1kHz - 1,5 kHz...
View ArticleForum Post: RE: ADC128S052
Hello,Gain error is the full scale error minus the offset error.Mike
View ArticleForum Post: RE: SRC4392 - what happens to digital overs?
Interesting. Thanks for the insight.any possible work-arounds come to mind? short of designing my own meters?The 4392 is a brilliant piece of engineering -- really wonderful performance.Best...
View ArticleForum Post: RE: About a setup of DAC5688EVM & TSW1400EVM.
Satoshi-san,I have modified the DAC5688 configuration file to fit the DAC5688 PLL mode. The changes are:1. changed the input clock configuration per page 33, table 5, PLL mode with CLKO. The assumption...
View ArticleForum Post: RE: hii need a help
on what basis you are saying teeth should be less than 50%.. is there any relation or expression....
View ArticleForum Post: DAC with standard I2C interface promotion
Hi BU teamMy custoemr Roch-chip wanted a DAC to meet below specs.1. must support the standard I2C interface, for GPIOs don't work as non-standard I2C interface under Linus OS.2. prefer at least four...
View ArticleForum Post: Can TLV320AIC3212 support Andriod, Win8.1, WinCE, and Win7???
Hi there,Can the TLV320AIC3212 support Andriod, Win8.1,WinCE, and Win7???Where can the drivers be found?Please adviseThank you in advanceAdam
View ArticleClik here to view.
Forum Post: RE: DS1248 EVM and SPI problem
Thanks for the Reply Bob.I am attaching here my screen shot as per Page 55 on the ADS 1248 DatasheetThe other question I want to ask you is about I am not providing any additional power supply other...
View ArticleForum Post: RE: How to interface PCM1794 to a host processor in I2S slave mode
PLL1700 is mentioned in PCM1794A datasheet. Would you recommend another PLL IC ? Thanks,Richard
View ArticleForum Post: TLV320AIC3120 External Microcomputer Control Using the EVM
Hi,If we pull up I2S_ENABLE node to 3.3V, can we control TLV320AIC3120 with the external microcomputer by using connector of P2?We believe that because 100P-JMDSS-G-1-TF(LF)(SN) is used in the EVM, we...
View ArticleForum Post: RE: Two questions about AMC7812 EVM
Howdy Mattew,Thank you for yuor kidly reply.It is really helpful to understand of AMC7812.Best Regards,Seung joon Lee
View ArticleForum Post: ADS 1148 not working (system monitor)
Hi,I am trying to work on ADS 1148, reading and writing on registers is happening but when i try to read the system monitor data it is not happening, DRDY pin is not getting low, can any one help.1....
View Article