Clik here to view.
Forum Post: TSW1400 giving spurious
Hi,           I  am working with ADS4229 and TSW1400 and in CMOS parralel mode.      my board is working fine. As i  applied some signal which is not  integer divident of...
View ArticleForum Post: ADS1255 Damage issue
I am using ADS1255 High Precision ADC for my Load Cell Application. Supply voltage to my Load Cell is 12V with respect to ground. The ADC diff voltage i.e. between AIN0 & AIN1 is 0-24mV with...
View ArticleForum Post: RE: AMC7823 temp sensor precision issue
Hello Matt,Device works in auto mode.Please see below init and simple read functionsvoid monitor_init(){Â Â Â Xuint16 dword;Â Â Â PORT_OUT(XPAR_CNTRL_GPIO_BASEADDR) |= AMC7823_RESET;...
View ArticleForum Post: RE: ADS1291 parasitic signals
I didn't get any reaction up to now.Anybody that can help me?
View ArticleForum Post: RE: LDC1000 - About the way of the usage
Hi, Thank you always for your kind support.Any update on this issue?Could you kindly give us an answer by the end of the week?I’m looking forward to your reply. Regards,Kanemaru
View ArticleForum Post: RE: Four questions about ADS1298 for EEG
Hello Mr.Ryan ,Thank you for quick reply.I undestood that settable Vref input range is under power supply,that I can input 24mV to Vref input.In respect of an amplitude of input wave and the reason of...
View ArticleForum Post: DAC5689 Real IF inteface - Independant & Differenct frequency plane
HelloI would like to know is the below configuration possible or Not.The DAC has 2 path, I want to put different frequency respectively channel1 and channel2.It means that the ouput frequency of DAC1...
View ArticleForum Post: RE: Help ADS1248 IDAC problem: no current
hi, Bob,Thanks for your quick reply. I connect the reister just as the schematic in my original post, It takes the place of the pt100 to form a 3 wire connecttion.The reigister setup values in my...
View ArticleForum Post: RE: Vehicle Loop Detectors
Hi Mr. Fomin,                    I am searching for some leads for designing a vehicle loop detection system. I just came across this post, may I get some information about the IC you mentioned in...
View ArticleForum Post: RE: Problem in SPI communication with ADS1148 EVM
Hello Mr.BOB. Thank you for your support. I have one more  queryI connected 4-20mA input from my mA source to the input (terminal T1 terminal no 2 and 3) of my circuit as shown in circuit diagram...
View ArticleForum Post: RE: balance and Unbalanced outputs tlv320aic3254
Hi, Bruce,I've asked my colleague to work with you on this issue.-d2
View ArticleForum Post: RE: AIC3106 MONO_LOM and MONO_LOP
Hi Hari,0. We are using LM4673 class-D amplifier.1. We have observed through i2cdump by reading Register-79 MONO_LOP/M Output Level Control Register. I am attaching i2cdump for your reference while...
View ArticleForum Post: RE: Can TLV320AIC3212 support Andriod, Win8.1, WinCE, and Win7???
Hi, Dang, SC,Unfortunately, the only drivers we have for this device are the ones that Dominik pointed you to.-d2
View ArticleForum Post: RE: High sample rate being the priority; 'ability to Connect...
Hi, Chris,Sounds very cool (pun intended!).I think you can definitely make a killer box using TI products! Unfortunately, we can't really help you here as we are pretty much focused on microscopic...
View ArticleForum Post: RE: PCM1754 Noise Problem
Hi, Seong Jong,Sorry that you are having trouble with our device. There are many reasons why this may be occurring.Things you may want to look at:- noisy power supply- noise picked up from a system...
View ArticleForum Post: RE: SRC4194 in SW mode should HW select pins be left floating?
Thanks Don,Thought that was the case, just wanted to make sure that those pins could be left unconnected,Thanks,Mark
View ArticleForum Post: RE: ADS8082 power sequencing
Sorry about my typo -- my post is regarding the ADS8028 ADC.
View ArticleForum Post: RE: How to use motherboard MMB0 which ADS1298 plug into?
You should receive an email shortly
View Article