Forum Post: RE: ADS8881 maximum SCLK
When I set the SCLK in ADCPro to 66.66MHz it changes it to 67MHz and the maximum data rate is 966.086lHz. This then reduces the clock to the ADC to 67MHz but also reduces the sample rate to...
View ArticleForum Post: RE: DAC161S997EVM
Hey folks, I wanted to add to this post as an FYI. I, too, had problems getting the Windows app to run, so the information above helped me get up and running with a serial console program. Some...
View ArticleForum Post: RE: TLV320DAC3100 problem on custom board
Dear Hartl, Thanks for the support please find the attached txt file having dump of page-0 and page-1 registers.RegardsVivek(Please visit the site to view this file)
View ArticleForum Post: RE: Serious problems with AIC3106 on OMAP-L137
Hi Jack,We can answer HW and register questions on this device. The DSP team supports the drivers.If you want me to take a look at the schematics and registers, please send them. For the register...
View ArticleForum Post: RE: How to set ADS1256 reference voltage and offset
Hi Ashish,I don't have much more information for you on this topic; I've gone out of my way to help support you. Our software is offered "as is" and is intended only for evaluating our products. For...
View ArticleForum Post: RE: LM97600 / LVDS input, output characteristics
Hi Asaka-sanIf the LMK04803 VOD (peak output) at 2GHz is 250mV, this means that the peak-to-peak amplitude is 500mVpp.Therefore it can provide a large enough output amplitude to drive the LM97600 CLK...
View ArticleForum Post: RE: overclocking ADC12D1800RF
Hi KrisI'm working to get someone to follow up.Thanks for your patience.Best regards,Jim B
View ArticleForum Post: RE: How to read ADC value from LMP90080
Hello,Ways to make the measurement more stable are:Make sure Vref = VA = 5V.Have caps on the Vref and VA pins, they should be a 0.1uf ceramic and a 1uF tantalum on the VA pin and a 0.1uF ceramic and...
View ArticleForum Post: RE: ADS1234 - Analog Input Control
Hi Vengadesh,The ADS1234 is a 4 channel version of the ADS1232. All information currently available with respect to the ADS1232 is on the ftp...
View ArticleForum Post: Spec Sheet question with LM96551
On pg 6/14 of the spec sheet for TI’s LM96551 (document SNAS511B, revised May 2013), it claims that the worst-case VPP current is 7 mA, and the worst-case VNN is 8 mA. At +/- 50V, this is a lot of...
View ArticleForum Post: RE: LMP91000EVM I2C, Stand Alone Mode
Thank you so much for the help Domencio!Regards,Jonathan
View ArticleForum Post: RE: AMC7812 can't i2c bus how use it? example code..
The power pad should connect to ground for best thermal conductivity, although if it wasn't, it wouldn't affect communication.AMC7812EVM and samples can be ordered through the following...
View ArticleForum Post: RE: CVBS to LVDS converter
AUNSOFT VIDEO CONVERTERConvert DTS HD, Dolby TrueHD audio to AC3, AAC, MP3.Support videos like TiVo, M2TS, MOD, VRO, MXF, VP6, MKV.http://www.aunsoft.com/video-converter/
View ArticleClik here to view.
Forum Post: tlv320aic20k record with high noise problem
HI! I have a comtom dm6467 board with tlv320aic20k audio chip,config the tlv320aic20k and record it(arecord) with 8Khz sample rate,but the sound play back (play back it in windows) with a lot of...
View ArticleClik here to view.
Forum Post: PCB design verification required for ADC ADS1230
Hi,We are using ADS1230 ADC for our weighing scale system. I have referred TI evaluation layout design for our new design which is shown below. So please check and verify the design and Let me know any...
View ArticleForum Post: RE: 2 questions about ADS131E08
Please, answer the second question,What is the ABSOLUTE MAXIMUM RATINGS:for AVSS – DVDD?
View ArticleForum Post: RE: ADS1259 EVM PDK
Hi Greg,Since the "ads1259-adcproplugin-2.0.0" is not support GPIO functions completely,Would you help to send the complete Labview source code for ADS1259 EVM PDK to me too? My email is:...
View ArticleForum Post: RE: LMP90100
I will try the protection and tell you the result ; but still could not find a solution to protect the IB1 and IB2 ( current outputs) from being shortcircuited to ground or high volatge; any...
View ArticleForum Post: RE: tlv320aic20k record with high noise problem
Hi, Duange,Unfortunately, we don't have a lot of support available for that IC.There are probably two places where noise could be generated: 1. clocking settings 2. PCB layoutI suggest you review...
View ArticleForum Post: RE: ADC PCM4204 with 4 channels at 192kHz
Hi, Martin,Our office is closed for winter break.We will respond to your post when we return. It might be as late as January 7th.-d2
View Article