Forum Post: RE: ADS124S08: Device Ready Flag (!RDY) high after RESET command
Hi Santiago Gonzalez T, Are you toggling CS before and after the RREG command? If not can you try bringing CS high, then low, then send the complete command, then pull CS high again? Can you also try...
View ArticleForum Post: RE: ADS1247: Anti-aliasing and filtering with software.
Well after looking at the high lighted article i did try to answer such questions. Fmod is 256 KHz for ADS1247 at 320 SPS. The anti aliasing filter frequency is set to 2.56Khz and ADS1247 ODR is 320...
View ArticleForum Post: RE: DAC8571: Convert 0 to 2.5 VDc to 0 to 60 mV
ok thanks. I have removed that transistor from the output stage and now i am getting good results...
View ArticleForum Post: ADC3221: what is reference voltage of ADC322x
Part Number: ADC3221 Tool/software: Dear PL AE one thing need consult. what is reference voltage of ADC322x? I could not find information associated with reference voltage in datasheet of ADC322x. I...
View ArticleForum Post: RE: DAC38RF82EVM: DAC chip and evaluation board provided file of...
What alternatives do you have? I would appreciate it if you could recommend it. And I would like to exchange the board I already purchased.
View ArticleForum Post: RE: TX75E16EVM: Transmit and Receive Ultrasound Simultaneously
Hello, As this device is NDA restricted, please contact us at support_us_afe_tx@list.ti.com so that we can assist you with your query.
View ArticleForum Post: RE: TSC2013-Q1: Single-touch or Dual-touch detection
Hi Daveon, Thank you. Reading the data sheet, the TSC2013 outputs the resistance value between the two panels. The host processor seems to distinguish between single/dual touche by determining whether...
View ArticleForum Post: TI-JESD204-IP: TI-JESD204-IP with DAC38J82 on AXKU3 Board - CGS...
Part Number: TI-JESD204-IP Other Parts Discussed in Thread: DAC38J82 , LMK04828 Tool/software: Hello, I am working with the TI-JESD204-IP core and the DAC38J82 connected through FMC connections to an...
View ArticleForum Post: ADC3683EVM: FMC to Zedboard connection
Part Number: ADC3683EVM Tool/software: Dear Team, My cusotomer wants to evaluate the ADC3683EVM by connecting the ADC368xEVM FMC (FPGA Mezzanine Card) connector to Zedboard. Is it possible? Do you...
View ArticleForum Post: RE: ADC16DV160: ADC16DV160\IF input noise
Hi rob, Thanks for your feedback. We checked by connecting Bandpass filter between signal generator and power divider also. Power levels for input frequency harmonic only reduced. Observed spurs...
View ArticleForum Post: ADS124S08EVM: ADS124S08EVM Not Showing Proper Sine Wave Output...
Part Number: ADS124S08EVM Tool/software: Setup Details: Below are my setup details: Function Generator Configuration: Signal Type: Sine Wave Frequency: 1 kHz Amplitude: 1.10 Vpp (Peak-to-Peak) DC...
View ArticleForum Post: RE: AFE7950EVM: Use with TSW14J50
Thank you very much David! Best regards, Thibault
View ArticleForum Post: RE: ADS1119: ADC Selection Advice
Dear Angel Rodriguez de San Miguel Bermudez Thank you for your reply. I will look into the ADS1115 in more detail, but is there a specific reason why this ADC is a better choice? Our application...
View ArticleForum Post: ADS131E08: power sequence
Part Number: ADS131E08 Tool/software: Hi team, I was wondering if there is any risk if digital 3.3V is prior to analog 5V as shown in below capture. (blue is 3.3V and Green is 5V). Thanks! Rayna
View ArticleForum Post: RE: ADS124S06: technical question
Hi Bryan， Currently using the IC default registers, unable to read the IC data. Below is the schematic.
View ArticleForum Post: RE: ADS1120: Sensor Detection
Hello TTD, Thank you for your patience. I am working however and will provide answers later today though. Best Regards, Henry Sarmiento
View ArticleForum Post: RE: ADC12DL040: ADC12DL040 design single-ended input
Hi Chase, Thanks for quick reply. I am designing an application that requires an ADC IC that uses single-ended input with a minimum sampling rate of 25MSPS. I cannot put buffer single to diff in...
View ArticleForum Post: ADS1119: REFP and REFN
Part Number: ADS1119 Tool/software: Hi Team, There is no differential Reference (REFP and REFN) in my design. Analog inputs (AIN0 and AIN1) are in the range of 0 to 3V. Is there a need to have a...
View ArticleForum Post: RE: ADS1247: Anti-aliasing and filtering with software.
Hi Nimit Vachhani, The over voltage requirements are defined by your system. For example, some systems are powered by a 24V power supply. Therefore, it is possible that someone could miswire the...
View Article