Quantcast
Channel: Data converters
Browsing all 89853 articles
Browse latest View live
↧

Forum Post: RE: ADC16DV160: ADC16DV160\IF input noise

Hi Esakki, The spurious is coming from the signal generator. Please use a bandpass filter on the output of the sig gen, I would connect it close to the EVM. Setup should be as follows: Sig...

View Article


Forum Post: ADS1299EEGFE-PDK: Single channel signal electrode with SRB1 and...

Part Number: ADS1299EEGFE-PDK Tool/software: Hi, I want to acquire EEG from a single electrode connected to PIN36 of J6 header - which is CH1 - AIN1P. I want to use SRB1. Where do I connect the signal...

View Article


Forum Post: RE: DAC39RF10EVM: API availability

Hi Joni, I am closing this post and will email you directly to follow up. Thanks, Rob

View Article

Forum Post: ADS9218: Current draw at 10MSps exceeds datasheet

Part Number: ADS9218 Tool/software: Hello, We've implemented the ADS9218 on a new design and the device is working nominally except that the current draw per device is 56mA when sampling at 10MSps...

View Article

Forum Post: RE: ADS1119: ADC Selection Advice

Hi Dharmesh, [quote userid="301387" url="~/support/data-converters-group/data-converters/f/data-converters-forum/1485066/ads1119-adc-selection-advice"]I would like to know if this device is suitable...

View Article


Forum Post: RE: ADC12DJ3200EVMCVAL: ADC12DJ3200EVMCVAL

Hi Sergey, Here are some of my thoughts: 1) Are you using the ADC GUI to configure the device? 2) What cryptic error? Please share any screenshots so we know what issues you are having. This will make...

View Article

Forum Post: RE: ADC12DJ3200EVMCVAL: ADC12DJ3200EVMCVAL

Hi Rob. Thanks for your reply. Yes we are using the GUI Application to configure the device. We are following the SLAU833a.pdf . Here is the screenshot of the error when the ILA Analyzer application...

View Article

Forum Post: DAC8806EVM: 3D model

Part Number: DAC8806EVM Tool/software: Hello Team, Do we ahve a 3D model avialble for this EVM? Regards, Renan

View Article


Forum Post: RE: ADS1278EVM-PDK: ADS1278V2EVM-PDK: Using your PHI to drive our...

Hello Daniel, Attached are the relevant Gerber files for both boards. e2e.ti.com/.../PHI_5F00_ADS1278EVM.zip Regards, Keith

View Article


Forum Post: RE: ADS1278-SP: Differential Input Impedance

Hello Albin, The temperature variation can be found in Figure 39 of the datasheet. Please note that the input impedance is closely approximated as a linear resistance, but there are non-linearities as...

View Article

Forum Post: RE: ADS1120: Sensor Detection

Hi Henry, Do you have any update so far? Best Regards, ttd

View Article

Forum Post: RE: ADS124S06: technical question

Hi switch, Can you provide us a schematic for your system? Please also provide the register settings you are using Thanks -Bryan

View Article

Forum Post: RE: ADS9218: Current draw at 10MSps exceeds datasheet

Hello Tighe, Thank you for posting on TI's E2E forum! Just to clarify this is for the AVDD supply only, correct? The configurations used for the data in the Electrical Characteristics tables is...

View Article


Forum Post: RE: ADS9218: Current draw at 10MSps exceeds datasheet

Correct, from pg. 8 of the datasheet. Our test matched the conditions stated in the header for the table. I will have to check for IP concerns before providing a schematic. I believe we have an NDA in...

View Article

Forum Post: ADS124S08: Device Ready Flag (!RDY) high after RESET command

Part Number: ADS124S08 Tool/software: Hi, I'm following the pseudo-code example from the datasheet (10.1.6, pg. 90) but when I send the RESET command and then read the status register (using the RREG...

View Article


Forum Post: RE: DAC38J82: DAC38J82IAAV

Hello, how do I find out the specific cause? Is it DAC38J82 itself?

View Article

Forum Post: RE: ADC12DJ3200EVMCVAL: ADC12DJ3200EVMCVAL

I am closing this post, as it is being handled offline.

View Article


Forum Post: RE: DDS39RF10: Is it possible to generate Frequency from 10GHz to...

Hi Anna, Yes, please refer to the datasheet and purchase an EVM to evaluate the DDS. Different output modes put different amounts of RF energy in different Nyquist zones. Regards, Rob

View Article

Forum Post: RE: DAC38J82: DAC38J82IAAV

Hi, Have you verified the spi timing on your boards, going into the DAC device is the same on a "good" and "bad" device? Have you checked power to the DAC on all supplied and other necessary signals...

View Article

Forum Post: RE: TSW14J50EVM:DAC chip and evaluation board provided file of...

If not, what products can we evaluate it with? And is it possible to exchange the boards I already purchased? Still selling stock on TI.

View Article
Browsing all 89853 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>