Forum Post: ADC084S021: I want to know spi mode of this
Part Number: ADC084S021 Tool/software: Hello, I would like to know the SPI mode of the ADC084S021. I checked the datasheet, but I couldn't determine the exact SPI mode. I assume it is SPI Mode 3...
View ArticleForum Post: RE: ADS7128: How to configure the I2C address？What is the purpose...
It is used for the voltage monitoring of 5V, with a 10KΩ pull-up resistor and a 4.7KΩ pull-down resistor.
View ArticleForum Post: DAC38J82: DAC38J82IAAV
Part Number: DAC38J82 Tool/software: Failed to configure the SPI Can you help me find out why
View ArticleForum Post: AFE4900EVM: AFE4900EVM sw to debug EVM board
Part Number: AFE4900EVM Tool/software: Dear, Admin I got an below response from TI, but I could not find where can I download the realted GUI SW and others. Please let me the way . 2025-03-04 06:06:31...
View ArticleForum Post: RE: ADS1015-Q1: ADS1015-Q1
Thank you very much, because our customers need to know these news
View ArticleForum Post: RE: ADS114S08EVM: The voltage across C88 is higher than the...
Hi Bryan, Thank you for your reply. I'll share your answer with the customer. When the customer has an additional question, I consult you again. I appreciate your great help and cooperation. Best...
View ArticleForum Post: DAC39RF10: Temperature Sensor
Part Number: DAC39RF10 Tool/software: Hi team, Could you let me know where the internal temperature sensor of DAC39RF10 is measuring? Is it die temperature as usual? (Double checking for customer's...
View ArticleForum Post: RE: ADS7830: Reading full range
Hi Tom, Here is my schematic. The input to oil_temp is a resistive load from 18-500 ohms (A VDO resistive temperature sensor)
View ArticleForum Post: RE: AFE58JD18EVM: Request for Allegro PCB file(.brd) data
Duplicate thread e2e.ti.com/.../afe5818evm-schematic-and-pcb-files-of-afe5818evm
View ArticleForum Post: RE: ADS1263: ADS1263 conversion time issue when using more than...
you mean ads1263 is useless for multichannel application... although it has 32k sps in single channel if so.... very disappointing ....
View ArticleForum Post: ADC12QJ1600: DDC Factor/Decimation factor
Part Number: ADC12QJ1600 Tool/software: Dear Team, What is DDC Factor/Decimation factor for the JMODE table given in Table 7-15 Is there any explaination or calculation for that. Regards, Liston
View ArticleForum Post: RE: DDC118: Design review
Hello, Are there any updates on the customer's inquiries? Thanks, JH
View ArticleForum Post: RE: AMC1035-Q1: Increased input bias current of AMC1035-Q1, if no...
Seems somehow strange, since I experience some other behaviour. I still have a positive input voltage over the differential inputs of the AMC1035 (ANIP, AINN) and the circuit behaviour changes, so...
View ArticleForum Post: RE: AFE58JD48: How to config JESD204B LMFS, K Parameters for 2...
Hi Sachin, After browsing more information, I have thought more about this issue, before I said that the statement that the two AFE58JD48 are considered as a 32-ch/8-lane JESD transmitter should be...
View ArticleForum Post: RE: AFE4960EVM: Discrepancy in AFE4960 EVM Output Measurements
Hi, Any updates? Thanks
View ArticleForum Post: RE: AFE58JD48: How to config JESD204B LMFS, K Parameters for 2...
Yes , By properly setting LMF parameter in FPGA you can handle this . This device supports JESD204B not JESD204C . In this example it looks like there are receiving data in only 2 lanes .(lane _mode...
View ArticleForum Post: RE: AFE58JD48: How to config JESD204B LMFS, K Parameters for 2...
I had to use the Xilinx JESD204C IP core to be backward compatible with the JESD204B because the JESD204B IP core was deprecated in the vivado version after v2022.1 (and probably a bit earlier). I...
View ArticleForum Post: ADS124S08: Thermal pad connection in QFN package with negative VSS.
Part Number: ADS124S08 Tool/software: Hi. My configuration: AVDD, IOVDD, DVDD 3.3V AVSS, AVSS-SW -1.2V Vref - external 3V Aincom - GND REFP0 - Ext Vref REFN0 - GND RECFOM - GND My concern is how to...
View ArticleForum Post: DAC8571: DAC8571IDGKR PSpice Model Request
Part Number: DAC8571 Tool/software: Hello, Could you provide the PSpice Model for the DAC8571IDGKR?
View ArticleForum Post: RE: DAC39RF10: Temperature Sensor
Hi Kazuki, Yes, this is die temperature. Thanks, Chase
View Article