Forum Post: RE: ADS1259: ADC conversions returning duplicate values.
Hi Michael Kruger, Unfortunately I am still unable to really see the images. When I click on the links the images are very small, which is not ideal for interpreting logic analyzer plots Can you...
View ArticleForum Post: RE: ADS8588S: ADC and AFE recommendation
Hi Chandra, The ADS8688S would be a fine choice for your application. The ADS8686S is a 16 channel, 16-bit device which may also be of interest to you. These are both successive approximation register...
View ArticleForum Post: RE: ADS8689: 800Vdc measurement
Hi Ludwig, Is adding a buffer like the OPA320 between your resistive divider and the ADS8689 input an option for you?
View ArticleForum Post: ADS1255: Example 2-wire configuration with UART in serial mode 0
Part Number: ADS1255 Tool/software: Dear Texas Instruments, I am currently using the ADS1255 for small projects with the SPI port and the Teensy 4.1. It works perfectly, and I am able to fully exploit...
View ArticleForum Post: DAC8742HEVM: DAC8742H carrier detect pin (CD) cannot detect...
Part Number: DAC8742HEVM Other Parts Discussed in Thread: DAC8742H Tool/software: I am using two DAC8742HEVM to develop HART communication in which one serves as transmitter and the other serves as...
View ArticleForum Post: DAC38J82EVM: and TSW14J57EVM unreliable - DAC fails to output RF...
Part Number: DAC38J82EVM Other Parts Discussed in Thread: TSW14J57EVM , DAC38RF82EVM Tool/software: Hello, I am evaluating the DAC38RF82EVM with the TSW14J57EVM pattern generator and DAC38RF8x Gui +...
View ArticleForum Post: RE: ADS1255: Example 2-wire configuration with UART in serial mode 0
Hi Giovanni Vitale, How are you planning on controlling multiple devices if the CS is low for all chips and they all send data at the same time? You either need multiple CS lines or multiple DOUT...
View ArticleForum Post: ADS8699: ADS8699IPWR: ECCN code with justification
Part Number: ADS8699 Tool/software: Looking for export control info, specifically ECCN code, for the following ADC ADS8699IPWR Thank you
View ArticleForum Post: RE: ADS8699: ADS8699IPWR: ECCN code with justification
Hi Mike, The ADS8699 carries ECCN code EAR99
View ArticleForum Post: RE: ADS1255: Example 2-wire configuration with UART in serial mode 0
Dear Bryan, Currently, I am testing a single ADS1255. Therefore, the raised issue does not apply. If I manage to make it work in two-wire mode with a UART, I will use the 8 serial ports of the Teensy...
View ArticleForum Post: RE: ADS131E06:Bits of data read are inverted.
Hi Dale. Thank you for your help. To check whether the RDATA command is one of the causes of the data corruption I replaced RDATA with commands that did not seem to affect the operation (WAKEUP and...
View ArticleForum Post: ADC08351: Inquiry about ADC08351 conversion clock
Part Number: ADC08351 Tool/software: What is the minimum clock for ADC08351 conversion? In the datasheet Electrical Characteristics table, it is listed as 2MHz. However, in Typical Performance...
View ArticleForum Post: LM98725: PGA gain of LM98725
Part Number: LM98725 Tool/software: Hello Ti, We have a question about LM98725. Now we are referring to RevH of the LM98725 datasheet. Regarding "PGA SPECIFICATIONS" at the bottom of page 9, there is...
View ArticleForum Post: TLV2548: TLV2548IPW
Part Number: TLV2548 Tool/software: Hi everyone, In my project, TLV2548 combined with Roche coil is used for AC three-phase current acquisition, and there are two questions about this chip, which are...
View ArticleForum Post: RE: ADS1298: Seems to be "malfunction" appear when electrodes...
Hi, How about the situation? I am looking forward to getting your support. Regards, Takumi
View ArticleForum Post: RE: ADS131M04-Q1: Help Needed: Basic Communication Between...
Hi KIRYOUNG YANG, Can you clarify "the intended setting is not being applied" and also the procedure of your setting? BR, Dale
View ArticleForum Post: TSC2200: Failed to read VBAT, VBAT 2, AUX1 and AUX 2 voltage values
Part Number: TSC2200 Tool/software: Hi Team, Failed to read VBAT, VBAT 2, AUX1 and AUX 2 voltage values, please confirm register and schematics e2e.ti.com/.../BTA-Read.txt...
View ArticleForum Post: AFE5818EVM: Can I use AFE5818EVM with TSW14J50?
Part Number: AFE5818EVM Other Parts Discussed in Thread: AFE5818 Tool/software: Hello. I have AFE5818 EVM now. But I heard that it needs TSW1400EVM. However, I can't buy it because it is obsolete now....
View ArticleForum Post: AFE4960: AFE4960 SPI Communication and EEG Configuration Issues
Part Number: AFE4960 Tool/software: Hi, I am working on integrating the AFE4960 into our design and am encountering issues with SPI communication and EEG configuration. Here are the details of what I...
View ArticleForum Post: RE: ADS9811: Interfacing TI Sitara with ADS9811
Hi Claus, Thanks for the information. With AM243x EVM, the FFT calculation can be performed by the R5F core using the data transferred to it from PRU (similar to the ADS8568 implementation). I will...
View Article