Forum Post: RE: AFE5832: AFE5832
As shown in the figure, K15 is SENo in the AFE5832 datasheet. Is this datasheet wrong?
View ArticleForum Post: RE: ADC12DJ5200RF: ADC12DJ5200RFAAV
Hello Shannon, Thank you very much for your information, it has been of great help to us. Taking into account the indicated date code, we will proceed to purchase the reference ADC12DJ5200RFAAV...
View ArticleForum Post: RE: ADC12DL2500: High speed data converter tool installation
Hi, It is trying to write some of the files it requires to a non-writable area meaning you don't have permissions to write to that area of the drive. Please uninstall, download HSDCPro 5.2 and install...
View ArticleForum Post: RE: ADS127L18: How to set DCLK frequency in Hardware Programming...
Hello Keith, I have 2 questions: 1. I change to one-lane (D0) serial mode (pin 3 HI) to get my data out and use a small FPGA on a board with 8x ADS127L18. The FPGA combines the 8 streams in one fast...
View ArticleForum Post: RE: ADS114S08B: ADS114S08B noise test issue
Hi Bo Xian Yeh, Can you please help provide the information I requested in the Notes section of the Thread Tracking Toolkit? Thanks! -Bryan
View ArticleForum Post: RE: LMP92066: LMP92066
Hi Erin, Similarly tell me for - DAC 1= -3.7V DAC 0= -2.8V Regards, Vaishak
View ArticleForum Post: RE: ADC3660EVM: How do I create a LOAD file for the ADC35XX EVM GUI?
Hi Miyahara san, When you load a configuration into the GUI, the GUI does not update, it only programs the part through SPI. There is no table comparing the register map and the features available in...
View ArticleForum Post: RE: ADS1015: part failing with unused inputs in a 24v system
Hello Scott, Following the datasheet's specifications for proper input operating levels and input protection against overvoltage, should provide the conditions for the part to function correctly. Not...
View ArticleForum Post: RE: ADS127L18: How to set DCLK frequency in Hardware Programming...
Hi Ton, DOUT1 is always an output, and should be left floating. All other DOUT pins DOUT[7:2] default as inputs, and can be used as GPIO pins. You can connect these pins to ground, or use...
View ArticleForum Post: RE: ADS1258: How to disable or avoid idle/standby mode
Thanks for the info. No, I don't want to restart the conversion process each time. That would waste a lot of samples and lower the sample rate considerably. I want to CONTINUE the existing sample...
View ArticleForum Post: RE: LMP92066: LMP92066
Hi Vaishak, Looks like the equation for the negative range is the same as the positive range, so: DAC1 = -3.7V = dec 3031, hex 0xBD7 DAC0 = -2.8V = dec 2293, hex 0x8F5 Thanks, Erin
View ArticleForum Post: DAC38RF84: SYSREF and start-up sequence
Part Number: DAC38RF84 Tool/software: Hello, I am driving the DAC38RF84 from an FPGA and do not require synchronisation of the DAC with any other devices. I gather from reading other posts that the...
View ArticleForum Post: RE: ADS8861: The Dout pin gives a constant high (i.e '1') as an...
Hi Haseeb, Thanks for your question. To confirm, what is the voltage of the input signal applied? What VREF and AVDD and DVDD values are you using? What happens if you change the input signal value?...
View ArticleForum Post: RE: ADS8861: The Dout pin gives a constant high (i.e '1') as an...
Hi Samiha . Thanks for responding. Input voltage (Differential voltage ) is a sinusoid voltage (peak = 5 ) . So I put voltage will vary from +5 to -5 V . AVDD — 3.3V DVDD — 3.3V VREF — 5 V . I am...
View ArticleForum Post: RE: ADS8861: The Dout pin gives a constant high (i.e '1') as an...
Hi Haseeb, Yes, if you set VREF to 5V and are applying a differential +/-5V input, you should be able to see it. Are your AINP and AINM inputs 0V to 5V, centered around 2.5V? The inputs cannot accept...
View ArticleForum Post: RE: ADS1258: How to disable or avoid idle/standby mode
Hi Lary Cotten, So, the START pin on the ADS1258 restarts the conversion every time. This is effectively true for all delta-sigma ADCs, because the filter has to flush if the conversion process is...
View ArticleForum Post: RE: DAC63002: Using an external reference with the DAC63002
Hi Yeongbin, Can you also share you schematic for the DAC and reference circuit? I am only seeing about a 100nA change in reference current when I ground the SYNC pin. Do you know how much current is...
View ArticleForum Post: RE: TSC2046: how to improve the Sensitivity of touch
Hi Sir Is there any update? Thanks Daniel
View ArticleForum Post: RE: ADC12DJ5200RF: ADC12DJ5200RFAAV
Hi Marco, Yes, the 10pc ADC12DJ5200RFAAV samples will be shipped in tray packaging. Best, Shannon Lippincott
View Article
