Forum Post: RE: AFE11612-SEP: How to get IBIS model
Hi John, I've attached the IBIS model. It should show up on the main TI site, so there's a mistake in there somewhere. e2e.ti.com/.../AFE11612.ibs Thanks, Erin
View ArticleForum Post: RE: TLA2024: I got the negative value, double confirm the way of...
Hi Toni Liu, I went over your I2C captures, They I2C communication looks correct. The first byte is 0x90 which is the device address and write bit. Second byte is 0x00 which is the pointer to the...
View ArticleForum Post: RE: AFE11612-SEP: How to get IBIS model
Thanks Erin, we'll continue our AFE SI sims with that model. -John
View ArticleForum Post: RE: DAC39RF10-SEP: Warranty policy
TI's standard terms apply https://www.ti.com/legal/terms-conditions/terms-of-sale/worldwide.html
View ArticleForum Post: RE: AFE5832: AFE5832
Thank you. I have another question to consult. Does the odd VCA register have no way to read and write anymore if we used AFE5832 in the pcb and PIN K15 is NC? Thanks.
View ArticleForum Post: ADS7138-Q1: About voltage monitor of Negative power supply's voltage
Part Number: ADS7138-Q1 Tool/software: Hello experts, Can it possible to monitor of the negative power supply's voltage in ADS7138-Q1? We want to monitor of -3.3V. Best Regards, Toru Kimura.
View ArticleForum Post: ADS7138-Q1: Regarding unused port
Part Number: ADS7138-Q1 Tool/software: Hello experts, ADS7138-Q1 has 8 channels. We will use 5 or 6 channels in it. Is it possible to connect a pull down resistor (about 100k ohm) to unused ports to...
View ArticleForum Post: RE: ADS1015: part failing with unused inputs in a 24v system
Thanks for the info Henry. Besides the lack of input protection, is there any other cause you can think of that would result in a short developing between the Vcc and Gnd within the device? In the...
View ArticleForum Post: ADS8861: The Dout pin gives a constant high (i.e '1') as an output .
Part Number: ADS8861 Tool/software: I am using the FPGA get the sampled data. I am using a 3-wire operation and so far I have taken everything from the data sheeet . Sclk :- 25 MHz (40 ns). Time...
View ArticleForum Post: ADS8568: -0.1dB Bandwidth
Part Number: ADS8568 Tool/software: Hi expert, What's the -0.1dB bandwidth of ADS8568? Only found the -3dB spec as below. Joyce
View ArticleForum Post: ADS114S08B: ADS114S08B noise test issue
Part Number: ADS114S08B Tool/software: Hi Expert, We are currently experiencing a non-pass noise test (ESD, EFT) issue in our ADS114S08B development project While the MCU and other surrounding areas...
View ArticleForum Post: DDS39RF10: DDS modulation for 1.5 - 6 GHz
Part Number: DDS39RF10 Tool/software: Hi expert, Need to verify with the team the following questions asked by my customer about DDS39RF10. As datasheet mentioned, DDS39RF10 can be implemented as an...
View ArticleForum Post: RE: ADS5296A: Input oscillation issue
Hi, I am coming up with possible issues 1) Because of clock Coupling : Can you check the oscillation without clock ? You can change clock frequency and check whether this "oscillation" frequency is...
View ArticleForum Post: RE: AFE58JD28: using link layer test modes with Quartus...
Hi, We havent done JESD204B capture using Quartus . What exactly is the issue you are facing ?
View ArticleForum Post: RE: AFE5401-Q1EVM: Substitute for TSW1400EVM
Hi, TSW1400EVM is obsolete and unfortunately TSW14J50EVM is not supported for this . TSW14J50EVM mainly used for JESD capture solution but AFE5401EVM had LVDS output.
View ArticleForum Post: AFE5832: AFE5832
Part Number: AFE5832 Tool/software: Does the odd VCA register have no way to read and write anymore if we used AFE5832 in the pcb and PIN K15 is NC? Thanks.
View ArticleForum Post: ADC12DL2500: High speed data converter tool installation
Part Number: ADC12DL2500 Tool/software: We would like to install High speed data converter tool to generate ADC configurations file for ADC12DL2500ACF but during installation (1) got below error and...
View ArticleForum Post: RE: AFE58JD28: using link layer test modes with Quartus...
Hi Sachin -- basically where to start for physical layer testing most specifically the transceiver analogue tuning stages using Quartus Transceiver Toolkit -- this seems to be fixed on PRBS test...
View ArticleForum Post: RE: ADS52J90EVM: Not able to evaluate using TSW14J50EVM
Hi, How did you get the EVM for ADS52J90 EVM file ? Is it though TI ? You can request that in ti.com portal
View Article
