Forum Post: RE: AFE58JD48EVM: An error occurs when automatically launching...
Hi, Can you please check the output voltage of these U2 and U10 ? If there is issue with this you should not see expected output (3.3V and1.8V) Which is the installation path for HSDC_PRO and...
View ArticleForum Post: RE: AFE4960PEVM: AFE2 of AFE4960P is not working
Hi Ryan "This is Nandy, posting on behalf of Aswath with a query related to Dual AFE. On activating the Dual AFE, I encountered an error and warning saying 'reset property not found' when trying to...
View ArticleForum Post: RE: ADS52J90EVM: evaluating ADS52J90EVM with TSW14J50
You can use Setup_ADS52J90_EVM exe only . I think you have already have this file .
View ArticleForum Post: RE: AFE5818: Schematics review
Hi, This is should be fine . I dont see any concern .Sorry for replying late . Somehow I missed this post .
View ArticleForum Post: RE: AFE58JD28: SYSREF Differential signaling issues
Sysref required from device requries common mode to be 0.7. In the datsheet it is explained how to shift the common mode . This might not be followed on EVM . In that case you see the difference is...
View ArticleForum Post: RE: AFE58JD28: SYSREF Differential signaling issues
No, sysref should not cause this . You can use adc test mode such as ramp/ toggle pattern/ constant pattern to see at the output
View ArticleForum Post: RE: ADS8588S: How to use only 4ch
Hi Tom, Thank you for your reply. OS[2:0] is set from FPGA at “000”, so it is in No oversampling mode, but unless both CONVSTA and CONVSTB are toggled, BUSY is High and Read data is not output. Also,...
View ArticleForum Post: ADS7039-Q1: ADC Precision
Part Number: ADS7039-Q1 Tool/software: Dear texas team, Greetings from Fervid Smart Solutions! We require the high precision ADC of 5 decimal points, should be able to measure the differential voltage...
View ArticleForum Post: RE: DAC39RF10EVM: Output Not As Expected
Hi, You can get a square wave by increasing the frequency of the output or do the modifications to the board. Regards, Geoff
View ArticleForum Post: RE: AFE4490SPO2EVM: Adding reverse voltage at Photodiode.
I hve one more question. The sentence "The bias voltage on INP and INN are set internally by the TIA front-end. The typical bias voltage is 900 mV." means: Is it referring to a voltage difference of...
View ArticleForum Post: AFE4490: AFE4490: Information of bias voltage in photodetector
Part Number: AFE4490 Tool/software: Greetings, We are conducting research and development related to pulse oximetry and are using your AFE4490 pulse oximetry product. We would like to inquire about...
View ArticleForum Post: RE: ADC12DJ5200-SP: CLK_P/N and SYSREF Input Waveforms
This actually didn't quite work on the board itself so I'll need to know how to adjust the LMX output gain in the IBIS model.
View ArticleForum Post: RE: ADS1258: ADS1258 Channel Data Read Direct Questions
Hi Bryan, First of all thanks for replaying! You are right, the data is different between CHID, but the thing is that in the MISO signal I am getting data (the 3 bytes of data) in the CHID where I...
View ArticleForum Post: RE: ADS122C04: Linux driver
Thanks for your reply. What is the most compatible 24-bit ADC driver that I can use, with minimum changes for ADS122C04?
View ArticleForum Post: RE: ADS131A02:ADS131A02IPBSR：POR(パワーオンリセット)について
Sorry. I will repost in English. Hello, Dear TI Customer Support Center I have a question about the ADS131A02IPBSR. Sometimes POR is unintentionally executed during operation. What are some possible...
View ArticleForum Post: RE: TX7332: Channel Delay Profile Settings Problem
Hi, When TR_SW_DEL_MODE is set to '1', the T/R switches of channels in a group (1-8, 9-16, 17-24, 25-32) are expected to turn on based on the last transmission in that group. Since you have programmed...
View ArticleForum Post: ADC128S022: Chip Select Signal
Part Number: ADC128S022 Tool/software: Hello, I am going to introduced ADC128S022 in my new design. I wanted to know whether I can tie CS pin permanently low to ground or not? I have only one ADC in...
View ArticleForum Post: RE: ADS1282: ADS1282 What duty cycle limits for the main clock?
Fine, thank you very much
View ArticleForum Post: AMC60704EVM: AMC60704EVM
Part Number: AMC60704EVM Tool/software: Please provide link for GUI and EVB user guide for AMC60704EVM Thanks Vignesh
View ArticleForum Post: RE: ADS8681: SPI CLK to SDO Delay contradicts max. SPI Frequency.
The falling edge, is out of scope (roughly a view hundred microseconds). For testing I used a simple mikrocontroller setup, which causes this delay between the CS edge and normal communication start....
View Article