Forum Post: RE: TSC2007: Need help with TSC2007
This is the answer of the chines company, they sell the board: Hi Dirk, sorry, we could not make the firmware just according to the above information. I think they need a step by step guidance
View ArticleForum Post: AFE11612-SEP: Noise or Interference
Part Number: AFE11612-SEP Other Parts Discussed in Thread: ADC128S102-SEP , DAC5675A-SP , While analyzing the IC datasheet and comparing it with the other ADCs and DACs available in the TI product...
View ArticleForum Post: RE: TCAN1462EVM: mechanical of TCAN1462EVM
Hi, It does not work. Could you send me those data: I need domensions: A-F Regards, Robert
View ArticleForum Post: RE: DAC81416EVM: Can't read data from DAC
HI, I try to access several register and reading it back(DEVICEID,SPICONFIG,PWDWN). They are echo the correct data. Only the DAC[0-15] echo the wrong data 0x0000 Would the DAC[0-15] are Write only?...
View ArticleForum Post: RE: DAC8162: Is the DAC output held while sending a refresh command?
Hi Katlynne, I talked with the customer and he has additional questions. Could you please advise? ï½°ï½°ï½° Of refresh commands (1), (2), and (3), I decided to remove (1) power-on reset because it is not...
View ArticleForum Post: RE: AFE11612-SEP: Noise or Interference
Hi Hridya, 1) The built-in temperature sensor is a feature. The device will not change the output depending on the temperature. 2) You can see power dissipation characteristics in the datasheet. When...
View ArticleForum Post: RE: ADS54J69: ADC is not responding on SDout line
Hello we are also using a DAC, DAC39J8, and this device is also failing to respond over SPI. I am including oscillograms of the SPI lines as they go into the ADC (specifically a read from the 0x04...
View ArticleForum Post: RE: ADS7138-Q1: about power dissipation
Hi Lawrence, Let me look into this and get back to you. Best regards, Samiha
View ArticleForum Post: RE: DAC121C085: Power supply sequence between VA and Vref
Hi Toshi-san, There is no sequence requirement. The datasheet also states that you can tie VREF and VA together without issue. Thanks, Erin
View ArticleForum Post: RE: ADS1291: The difference between the various lot under x-ray
Hello Michael, I would like to take this offline and have sent you an email. Can you please respond over email?
View ArticleForum Post: RE: DAC8750: The event occurring both alarm set and data send at...
Hi Yoshikazu-san, Section 8.5.1.4 of the Datasheet (page 31) mentions that not having the correct amount of SCLK cycles will result in incorrect data being programmed into the registers. Section...
View ArticleForum Post: RE: TCAN1462EVM: mechanical of TCAN1462EVM
Robert, A - 72.2 mm B - 115.7 mm C - 106.8 mm D - 63.3 mm E - 4.4 mm F - 4.4 mm Please let us know if you have any other questions. Regards, Eric Hackett
View ArticleForum Post: RE: ADC3683EVM: ADC3683EVM
Hi, Yes, the TSWDC155EVM will work with the ADC3683EVM, however, we do not have anything to support that right now. We hope to have something in a month or so. The GUI that is linked on the product...
View ArticleForum Post: RE: ADS1220: Power consumption question to compete with AD4130-4
Hi Gary, ADS124S08 and ADS1220 seem like possible replacements for this device. This E2E post goes more into detail on the differences in power consumption between these two devices: (3) ADS1220: vs...
View ArticleForum Post: RE: DAC8162: Is the DAC output held while sending a refresh command?
Hi Shinichi-san, (a) If you are using the SW reset, depending on the state of DB0, either only the DAC data registers will be affected (when DB0= 0), or all registers will be affected (when DB0= 1)....
View ArticleForum Post: RE: DAC63204EVM: DAC63204EVM
Hi Mitali, Your SPI mode is correct. The data is being shifted out on the rising edge, and the DAC will capture it on the falling edge. You will not see anything on SDO until SDO is enabled, and I...
View ArticleForum Post: ADS8887: occasionally got stuck by outputting all zero data
Part Number: ADS8887 First, let me provide some backgrounds. In one of our 4-20mA current loop-powered sensor products, we utilize Analog Devices' AD7989-1, along with several op-amps and an MCU, to...
View ArticleForum Post: ADS127L18: is the DCLK for ADS127L18 a continues clock or burst...
Part Number: ADS127L18 Can I use DCLK to drive FPGA logic, it needs to be a continuous clock.
View ArticleForum Post: ADS127L18EVM-PDK: Error message 0xFFFFEC78
Part Number: ADS127L18EVM-PDK After I connected the 6V power, then USB power, open the EVM app on the PC, and this message pop up. Anyone know how to fix this.
View ArticleForum Post: RE: TSC2007: Need help with TSC2007
(+) TSC2007 probe failed with AM3352 (SDK 07.00) - Processors forum - Processors - TI E2E support forums Let me know whether you can compile the driver into the kernel with above guidance? Following...
View Article