Forum Post: RE: ADS1241 Registers
Hi Hamid,An interrupt is not a called function from the main loop. The interrupt gets called either by an edge or level change at the input of the pin where DRDY is connected. The way this is...
View ArticleForum Post: RE: AIC3120: Which component should we use in order to detect the...
Hi community member,Would you please provide your comments for my question?It will be very helpful to support customer.Best regards,Kaka
View ArticleForum Post: RE: AIC32x4: H/W AGC behavior
Hi Don, Hartl,Would you please provide your comments for my question as soon as possible?We need to answer the question to customer ASAP.I apologize to press you. Best regards,Kaka
View ArticleForum Post: RE: PCM1795 How to change DSD Mode to PCM Mode
Hi, Dominik-san,Thank you for your cooperation quickly.We understood that we must continue to apply the SCK.If we obtain questions from customers, could you please advise to us?Thank you so much.Best...
View ArticleForum Post: RE: ADS1298ECGFE-PDK Driver problems
hi Greg Hupp,have successfully installed the ads1298 evaluation software on windows xp sp2 but while starting the application there displays error "labview:an input parameter is invalid.for example if...
View ArticleForum Post: TAS5711 Biquad
HelloPlease le me your advice about how to make All path filter in detail in case TAS5711.I think Allpath filter( f0, bandwidth) can be designed using Phase shift.Is it correct?Best Regards
View ArticleForum Post: RE: cannot install driver for ADS1298 to Windows Vista....
hi Greg Hupp,i have downloaded the latest version of the software.i am using the cracked version of windows Xp sp2 32 bit version,is that a problem.regards,shreedhara manni
View ArticleForum Post: RE: ADS8556 CONVST glitch - 2nd assertion of BUSY
I would love to be able to trigger the scope directly on the failure case, but unfortunately falling edge trigger on CONVST is not always the failure case. It actually took quite a bit of time for me...
View ArticleForum Post: RE: Self offset calibration ADS1247
Hello again,I have finally found the issue with the SELFOCAL command. The time between the last falling edge of SCLK and the slave deselection (/CS being pulled high) was not long enough. The...
View ArticleForum Post: RE: ADS1281EVM input divided by 2?
Chris, I've received the new ADS1281EVM and was able to reproduce the same tests and this time i have the good results, the output is not divided by two.So the kit i was using at the first place was...
View ArticleForum Post: RE: TLV320AIC3254 DSP not working
This sounds exactly like my problem. Did you ever figure it out? I can't believe the question was never answered.
View ArticleForum Post: RE: Improving the Quality of Playback and recording using...
Hi Converter Apps Team,Once again Thanking you for all your inputs and support you gave us all these days. Please refer to the below link for...
View ArticleForum Post: RE: ADS131E08 gets stuck
Greg,In computer '11' and '0x0B' will give you same value. '11' is with decimal. You can not get decimal '17' with writing '11', you can get it with '0x11'.If there is no issue for the code, lets back...
View ArticleForum Post: RE: AIC3254 transition from EVM
I've scoured the forum and it seems other people have encountered the same problem. I can't seem to resolve it and I can't spend any more time trying to get this part to work. I think that I've...
View ArticleForum Post: RE: Inquiry regarding TLV320AIC3101 system configuration
Okui-san,I will investigate this issue and get back to you shortly.Is it possible to forward a higher resolution schematic? The current schematic is a little bit hard to read.
View ArticleForum Post: RE: ADS1299EEG-FE Demo Kit - Daughter-board schematic discrepancy
Thanks for clarifying Ryan,Also, just a relevant note, it appears that Table 7 in the Demo Kit User's Guide (slau443.pdf or http://bit.ly/17xnw89) has the J5 pins backwards. Following the actual PCB...
View ArticleForum Post: RE: Seeing "plateau" values at 0x__FF intervals in ADS8319 output
Hi Swapnil,Could you please share your schematic? Is it possible for you to measure the voltages on the supply, reference, +IN and -IN pins of the ADC when it is in the condition you...
View ArticleForum Post: RE: LMP90100/90080 input protection
Sorry - I meant Vref. VA is 3.3V. I can protect the input to the VA rail; it's the potential drops below GND that I'm worried about.Mike
View ArticleForum Post: RE: ADS1255 T16b & other time constraint
Hi Alan,In your case fCLKIN = the crystal frequency, 7.68MHz.The "t16b" timing requirement still applies. If your processor has trouble meeting this restriction, then we recommend "re-clocking" the...
View Article