Quantcast
Channel: Data converters
Browsing all 90367 articles
Browse latest View live

Forum Post: Interfacing ADS1282 with Tiva C Series TM4C1294 Connected LaunchPad

Hi,I have to interface ADS1282 with a microcontroller. I need to use SPI to do so. I went through the datasheet and its pretty confusing, I didn't get any idea where to start with. I would be happy if...

View Article


Forum Post: RE: TLV320AIC3107 Class D speaker amplifier

Hi,All of the data we collected is in the datasheet. If you don't see it there, we don't have the data.You can find a recommended layout and decoupling values in the EVM layout and schematic which are...

View Article


Forum Post: RE: Official Software / Firmware Thread (GUI, MSP430, MATLAB,...

Hello Jiaqi,Apologies for the delay.I am out of town at the moment, once I'm back I will look into it.In the meanwhile, what version of LV do you use?

View Article

Forum Post: RE: LDC1000 labview vi problem

This node waits for a notification from the main GUI to stop this deamon.

View Article

Forum Post: RE: About a register of LDC1000EVM

Hi,Power wii be off in default configuration, so you need to write 0x01 when power on, you can`t keep it after power off.Regards, Sunny.

View Article


Forum Post: TMS320C6713 aic23b

I am just beginner with my DSP program. I got a simple example about with this board. The result is good, but i can't figure out the relationship between my input and the binary number. /* * main.c...

View Article

Forum Post: LDC1000EVM reprogram the MSP430F55281

Are there any instructions for using Code Composer to reprogram the MSP430F55281 already on the LDC1000EVM board.Is this possible?

View Article

Forum Post: RE: LM49352 timing of the I2S port

Hi Don,Is not the same customer. I saw that post but the apps note hyperlink is broken it took me to the roadmap of ESP. I search for the app note and yes indeed it has the bus timing, Thanks. i am...

View Article


Forum Post: RE: Respiration from body using ADS129xR EVM

Hi James, Thanks for checking out the ADS1298R!Are you able to see the on-board respiration signal? This would require JP34 [1-2] and JP35 [1-2].I found that the Respiration measurements with ADS129xR...

View Article


Forum Post: Guidelines for determining target metal composition using the...

I see in the data sheet references being able to identify the target metal composition using this device.  I'm assuming there is some sort of inductance signature associated with every conductive...

View Article

Forum Post: ADC SPI register settings for JESD link parameters on ADS42JB49EVM

Hi e2e,Can you provide the proper ADC SPI register settings for the attached JESD link parameters, or is there a C code API available for setting up the ADC?Thanks for your help;John Wiemeyer(Please...

View Article

Forum Post: RE: ADS8568 power supply problem

Hi Justinas,You are correct, there should be no reason why you cannot have the AVdd separated (and greater) than the DVdd input to the ADS8568 so long as the analog and digital grounds are tied...

View Article

Forum Post: ADS 1191 or 1192 Performance Standard

There are industry standards on ECG front-end such as AAMI or IEC.  Just wondering if these chip would be able to satisfy the relevant requirements (e.g., frequency response, input impedance, CMRR,...

View Article


Forum Post: TSW1400 EVM and ADS62P49 EVM

Hi TI,I am using TSW1400 EVM to interface ADS62P49 EVM via CMOS.Connected CMOS Pin 1 on TSW1400 to pin 39 of ADS 62p49EVM board.User LED 3 , 4 is not ON in the TSW 1400 boardI want to simply capture...

View Article

Image may be NSFW.
Clik here to view.

Forum Post: ADS 1178: transfer function question

HiI was testing a Data acquisition system based on 1178.I plotted voltage to count output and found this graph Test condition: Vrefp: 2.5V, Vrefn=0, Avdd=5V IOVdd=3.3V DVdd= 1.8VSampling rate=20khz.All...

View Article


Forum Post: ADC08D500 Startup Time

Hello, I'm using the ADC08D500 and am observing long startup times on the order of 10 seconds on initial powering. Specifically, it takes ~10 seconds from when the the chip is first powered to when...

View Article

Forum Post: RE: DAC7731 / 8bit truncation for the 24bit data

Hello Toshiyuki-san,There are a few options that will depend on your application.Can we bring this conversation offline? Is it okay to contact you to your E2E registered email?

View Article


Forum Post: ADS5407 Logic Levels

I am developing a new design with the ADS5407 Dual Channel ADC, and I have a logic compatibility issue. The differential input levels listed in the datasheet are identical to the output levels rather...

View Article

Forum Post: RE: ADS1191 logic levels

Hello Florea, Absolute Maximum rating for digital inputs is DVSS - 0.3 V to DVDD + 0.3 V. In the Electrical Characteristics table, the important spec to remember is the level at which an input is...

View Article

Forum Post: RE: ADS 1191 or 1192 Performance Standard

Hi Josh, Our ADS129x devices can be designed into a system that is AAMI/IEC compliant. However, you will not meet these standards by using these devices alone. Customers must design the necessary...

View Article
Browsing all 90367 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>