Quantcast
Channel: Data converters
Browsing all 89864 articles
Browse latest View live

Forum Post: RE: I need help to read ID and other registers from ADS1291

Can you provide a screen capture of the SPI signals from oscilloscope?  Sometimes it is easier to identify problems by looking at the signals.

View Article


Forum Post: RE: Can the PCM5102EVM-U run at 384k?

Hi John,You would need to use a direct I2S input from a different source such as the Audio Precision PSIA to get this sample rate.

View Article


Image may be NSFW.
Clik here to view.

Forum Post: alaw miniDSP aic3254

Hi, I attempting to solve next task:Receiving audio data from AIC3254 with alaw compression in miniDSP. I create the next scheme in PPS:That is correct?Next, I connect to mic_in the signal from the...

View Article

Forum Post: ADC12J4000 input signal BW

Hi,In the datasheet for the ADC12J4000 EVM, it states that the board contains a "Transformer-coupled signal input network allowing a single-ended signal source from 400 MHz to 3 GHz". The signal I am...

View Article

Forum Post: RE: PLL frequency of TLV320AIC3254 is 210 MHz

The 210MHz is above the max. CODEC_CLKIN spec (as you noticed). What do you observe if you set J=10? Is PLL_CLKOUT on GPIO flat (no output) in this case? At what J setting do you get the expected PLL...

View Article


Forum Post: RE: DAC+FPGA+ADC (ADC12J4000)

Hi,In the raw 12 bit ADC mode, is the serial bitrate 2xDEVCLK for EACH of the 8 serial lanes?Thanks!Rosanah

View Article

Forum Post: RE: TLV320DAC3100 beep generator which CLK Needed

In ordr for the beep generator to work, you will have to have a BCLK and WCLK. This can be done via an external I2S master or you can configure the AIC to generate the clocks internally.This...

View Article

Forum Post: RE: PCM1798 always outputs full scale

(Please visit the site to view this file)The load is a 1/4-watt  1MOhm thin metal film resistor, across Vout+ and Vout-.The waveforms shown are taken in MONO mode, left channel.

View Article


Forum Post: ADS1278 unstable

I have a few questions about a potential instability issue with the ADS1278. I have a system where the ADS1278 is operated in low speed mode with an input clock rate of 12.5MHz. The ADS1278 is being...

View Article


Forum Post: DAC5687 interface to TFR3705

Hi,I’m working on an interface between the DAC5687 and the TRF3705 direct IQ modulator.  I’ve been using the application report (SLAA399 – passive terminations for current output DACs) to design the...

View Article

Image may be NSFW.
Clik here to view.

Forum Post: RE: DAC7811 adjusts voltage option

[quote user="Fawad Munawar"]I am using 8 of AFE5809 chips to get more channel options .My main concern  is In the  TGC section producing VCNTL signals.(VCNTL_IN_P/VCNTL_IN_N) This signal is an analog...

View Article

Forum Post: RE: Can't install LDC1000EVM driver, using macbook and fusion 6...

Hi Anton,Try updating the device.In the GUI try using Tools > Flash Firmware.  After a couple seconds you should see "1 device(s) in BSL found."  Then, select "Open..." and navigate to the firmware...

View Article

Forum Post: RE: PCM3168A EVM?

Hi Don,Thank you very much for the suggestion to check out the PurePath Console Mother Board. I've had a look through the datasheet and it does include the PCM3168A codec as you said. My only concern...

View Article


Forum Post: RE: ADS1274 maximum differential input

Isaac -Yes, the input can go to the limits in the datasheet without damage to the device.However, the issue becomes that you are saturating the modulator of the ADC, hence the instability.  Normally,...

View Article

Forum Post: RE: Sensor frequency at LDC1000

Let me just add that to change the oscillation amplitude, you need to change reg.04 value.

View Article


Forum Post: RE: Instability of Proximity Data

Hello Avinash,You are absolutely correct that by reducing the target size you will be able to avoid saturation. As long as you are still able to meet your resolution requirements, this is an excellent...

View Article

Forum Post: RE: ads5242 glitch at 0

Ah, great!  Thanks for letting me know.Regards,Richard P.

View Article


Forum Post: RE: TLV5614 DAC

Hi Thiyagarajan,The falling edge of FS (Frame sync input) pulse indicates that the serial data from serial input register has shifted to the TLV5614.Page 7 of the datasheet explains the timing diagram....

View Article

Forum Post: Datalogging with LDC1000EVM

Hi,I downloaded the GUI update to enable data logging and I am finding that the the the data will accumulate for up to two hours before the data collection hangs and the last data point is displayed...

View Article

Forum Post: RE: LDC1000 GUI Disconnect

Hi PAN-M,What does it show up as? "EVM" or "LDC1000EVM".  If it shows up as "LDC1000EVM" you need to force install the driver:---------------------------------------------Windows should install the...

View Article
Browsing all 89864 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>