Forum Post: Some questions about LDC1000
HiI'm looking into the LDC1000 Evaluation Board.All Questions are related to EVM.I want to compare these parameters with my test result.(I'm not certain)Q1. oz of coil pattern?Q2. How much current or...
View ArticleForum Post: RE: LVDS to Digital RGB
Hi Ehsan,You would know a lot more about this than I would but I thought I might mention it anyway in case it helps. Did you check your traces on the PCB are same length?Your signal can be clean but...
View ArticleForum Post: RE: Multiple(3) Ads1248 on same SPI line
1. Does that means putting Start pin low put device in sleep mode.2. When I send a start pin pulse i.e high to low & wait for DRDY pin to go low. Then start is low already &drdy pin go low then...
View ArticleForum Post: ADS7954 / about pin connections
Hello, Could you please let me know reccomended pin connections of ADS7954 TSSOP PKG ? (1) GPIO1~3Should we pulled up or pulled down these pins?If yes, please let me know recomended resistor value....
View ArticleForum Post: RE: ADS1299 and MSP430F5529 issue reading ID register
After several attempts i got the correct ID value, the problem is that i just get this correct value sometimes, when i plug and unplug the AC regulator of the EVM, but it is a really random behavior....
View ArticleForum Post: RE: TLV320AIC3206 for Hearing AID
Hi, Avraka,Pretty much every device in our portfolio meets your limited requirements. Do you have more requirements to help us filter down the number a little bit?Have you tried using our selection...
View ArticleForum Post: RE: PCM1803A Input Pullup
Hi, Bruce,Welcome to e2e, and thanks for your interest in our products.The PCM1803A indeed has internal biasing to make is easier to use in audio applications. Since this parameter is not critical in...
View ArticleForum Post: the SPI interface between ADS1298 and MSP430F5529
Hi everyone,When I try to make SPI interface between ADS1298 and MSP430F5529, it always doesn't work. Hope to get some help.The following is the code.#define CS_HIGH (P2OUT |= 0x20)#define CS_LOW...
View ArticleForum Post: RE: ADS1218 - ssi clock
Hi Bob,Thanks for the detailed description . It gave me brief insight about the procedure . This is the sequence i think ADS follows:As soon as i keep the PDWN, RESET and DSYNC pins logic high the ADS...
View ArticleForum Post: RE: PCM4222 design questions
Hi, Jared,Cool! (pun not really intended)How hot is the IC getting?The OPA1632 was the best IC to be mated to this device when it was released. Unfortunately, I don't follow the op amps that our op amp...
View ArticleForum Post: RE: Sound card registration fail
Hi, Sangly,I hope that someone in the community can chime in and help you, as I said in this post, we don't provide drivers or driver assistance.-d2
View ArticleForum Post: RE: Can the PCM5102EVM-U run at 384k?
Hi, John,I have asked my colleague to give you some suggestions.-d2
View ArticleForum Post: RE: PCM5100A and the Sitara processor
Hi John,Here's the appropriate forum: http://e2e.ti.com/support/arm/sitara_arm/default.aspxRegards,Gautam
View ArticleForum Post: RE: Obtaining 128 kHz BCLK on TLV320AIC3105 in DSP mode for 16...
Hai DonThanks for offering help and i really appreciate your effort.Regards
View ArticleForum Post: Instability of Proximity Data
Hello All,I wanted to use my LDC1000EVM to evaluate the distance from a metallic target. I am interested mainly in the measurement of extremely small distances (my main target is nm range). Hence...
View ArticleForum Post: RE: Simulating 3 terminal electrochemical sensor on LMP91002
Dear anonymus,the approach you have in mind is correct. Please make sure that the curernt source you are using can be used in a floating mode. Let me explain better. I've done the same test wiht an old...
View ArticleForum Post: Password for source "Source_ads129x_v1p1p1A.zip"
Hi,Please send me password for source "Source_ads129x_v1p1p1A.zip"My email address is ibiro_ro@yahoo.comThanks.
View ArticleForum Post: DAC 8734EVM powering UP/initialization
Hi,I just bought DAC8734 board.Can anyone tell me the powerup sequence pins in EVM.Which pins does the following signals denote.DVdd-IOVdd-AVss-AVdd-I know this is the sequence for powerup from the...
View ArticleForum Post: RE: Problem with AIC3204 ADC at 8kHZ
Hi Don,Thanks for your response, mentioned resource helped me alot configuring the codec's ADC/DAC for 48khz/32khz but my problem is my configuration is not working for 8khz/16khz i am correctly...
View Article