Forum Post: RE: ADS1241 Registers
Hi Hamid,What about your other digital pins? Did you verify those at the pins of the ADS1241?Best regards,Bob B
View ArticleForum Post: RE: TVP5147M1 Status2 Resister
Dear, Steve-san.I appreciate your teachings, again. I can imagine it would be environment oriented. Thanks again. Best Regards,
View ArticleForum Post: RE: Audio DAC plus Audio amplifier Availability
Hi Justin, Outside of the absolute maximum ratings, the part may malfunction, whereas outside of specified range the part may not meet the specs defined in the electrical characteristics.Take a look at...
View ArticleForum Post: RE: ads1248 Basic Application
Hi Bob/Joachim,Thanks for all you help. I will proceed and complete the design and revert when I have the PCB board.Regards,Tom
View ArticleClik here to view.
Forum Post: About ADS1292R SPI Problem
I use MSP430F5529 to control ADS1292R, it converted data in continuous mode,But the timing seems to have a problem.Below is a screenshot of the oscilloscope, the first (red line) is the DRDY signal,...
View ArticleForum Post: RE: TVP7002 unused inputs
Thanks Steve.For the PLL loop filter - do you suggest to use NPO caps ? or X7R are also good enough
View ArticleForum Post: RE: PurePath Studio Code Generation Problem
I can not reach the below file on http://pps.ext.ti.com/Release Notes Version 5.95 Build 1 Rev. 25538I think the link is broken??Can someone send the link for this file.. (Or the file itself)
View ArticleForum Post: RE: set sampling rate AIC3204
I have already downloaded it. However, as I said I don't know how it works. It doesn't detect my board TMS320C5515 EVM.
View ArticleForum Post: RE: 245.76 MHz Filter "FLT1" on the ADS62P49EVM
Hi,This TF2-Q5EC1 filters are not available anymore, could you please suggested an alternative that can be populated on EVM board.Thank you and kind regards,Volodymyr
View ArticleForum Post: RE: ADS1299 Wiring & Start
Hi Have a look at the other signals on the SPI interface there is SPI_in and SPI_out (which have you shown on the graphs?) What is the START signal and the CE signals doing??
View ArticleForum Post: RE: ADS1299 Microcontroller Interfacing Issues
Hi I've just got the ADS1299 EVK working with an external uP (so there is hope!!)Do the signals appear in the right place on J3 of the EVK?? BL
View ArticleForum Post: ADS1299 Mid rail reference
Hi I'm working on a ADS1299 schematic and I have a question:On the EVK there is a external OPA376 which drives the Bias electrode, its reference point is the mid point of a resistor totem pole. As this...
View ArticleForum Post: RE: ADS1299EEG-FE Source Code
The email address on file should be fine.Thanks, Alex
View ArticleForum Post: RE: Password required for...
Hi Tom,Please send me the password at high priority. It is very urgent for me. If you don't have the source code for the software of ADS1298ECGFE , then please clearly tell mejaballimaher@yahoo.frThanks
View ArticleForum Post: RE: TSW1200 VHDL Code
Can I get the VHDL/Verilog Code for the TSW1200? Interfacing A ADS6424 EVM board to a Xilinx Zynq eval board. Mike.st.vincent@gmail.comThanks
View ArticleClik here to view.
Forum Post: RE: Configuring AIC3204 for 8Khz Mono ADC and also DAC
Hi Shaym: If you want to fast setting the AIC3204, you can use the picture below: You can get the code from the script. And the hardware connection should be like the...
View ArticleForum Post: RE: How do i connect two 3-wire RTDs in a LMP90100 ?
Hello Dongbeom,Let me help answer your questions. See below.Who can verify my schematic ?>> Schematic looks good. 2 3 wire RTD's each with there own IB current source and reference (VREFP -...
View ArticleClik here to view.
Forum Post: RE: Problem to initialize ADS131E08
Greg,After making stronger signal driving capability for SCLK, MOSI and CS\, I captured the following picture.Ch3 is SCLK with 5MHz; Ch2 is DRDY, Ch1 is MOSI with 0xAA data, Ch4 is CS\ signal.I...
View Article