Forum Post: RE: ADS1248: NTC resistor detection solution
Hello Joseph, Thanks for your great support, there are some feedback about your questions below, please also give your comments. Now they want to use TGMAA103G39HAD(purple curve), the resistor range is...
View ArticleForum Post: RE: ADS7951: About absolute maximum ratings of the REFN and REFP...
Hi Hiroaki San ADS7951 is designed to work with external reference voltage between 2V to 3V. Please refer to electrical char table on page no. 12 of datasheet. So maximum voltage than can be applied to...
View ArticleForum Post: ADS1220: Internal Temperature Sensor register set time
Part Number: ADS1220 Hi, I am using the ADS1220 to get some readings, with a differential input coming in on AN1 and AN2 and another input on AN0. I am also reading the internal temperature sensor of...
View ArticleForum Post: XTR105: design 4-20mA device from PRESSURE SENSOR
Part Number: XTR105 HI, I want to use XTR105 to design 4-20mA device. The OC18 PRESSURE SENSOR is input source. How about to connect the XTR105 ?Do you have any suggestions for me? So please advise me....
View ArticleForum Post: RE: TLV320AIC3120: I2S Recording
Hi luis, I am interested in capturing mic data from codec,By using host processor/controller. How can it be possible,Please help me out.
View ArticleForum Post: RE: Can ADS54J66EVM interface with ZC706 Dev-board correctly?
Yuzhen, 1. If you plug the ADS54J66EVM directly into the ZC706 with out using the TSW14J10EVM , you will not be able to use the TI HSDC Pro GUI. Without this GUI, you will have to generate your own...
View ArticleForum Post: RE: PCM2912A: PCM2912A DSN file
Dear Diego Thanks for your reply Looking forward your DSN file
View ArticleForum Post: RE: PCM55: Difference between PCM55HP, PCM55HP-1 and PCM55HP-3
Hi Diego, Thank you very much for your reply. The information is helpful. Thank you and Best regards, Raku
View ArticleForum Post: RE: SRC4184: Ready output is stuck high
The LRCKO is derived from a VCXO 24.576 MHz divided down by 512 to 48K. LRCKI is derived from a 125Mhz clock oversampling an AES3 input to create an effictive LR clock. That LRCK will inherently have...
View ArticleForum Post: RE: DAC38J84: DAC38J84 in 4 channel mode with NCO enabled
AD9164 remote test tool is convenient,I use it to test my idear,due to lower sample rate limit,the sample rate is 2 times the condition of my application. I get the expected output at 1600MHz(2 times...
View ArticleForum Post: RE: ADS1220: SPI I/F without CS connection to MCU
Bob san Thank you for your support always! And we appreciate your help always. We would like to confirm an additional content. When our customer uses Single-Shot Mode, is it the same as Continuous...
View ArticleForum Post: RE: ADS54J60: ENOB parameter
Hi Tommy, What is the test conditions for this ENOB value? We have table of ENOB vs Freq in J40. Do we have that table in J60? Thanks. - YY
View ArticleForum Post: RE: ADC14L020: Tapped Inductor Bandpass Filter Design
Hi Alex I'm looking into this. So far I haven't been able to locate that National Semiconductor article. Can you please provide a link to the document if it is on the web, or attach a scan if you have...
View ArticleForum Post: RE: DAC7760: Connect to Launchxl-F28377S
Hi! Kevin, Thanks for your support. I'll check TIPD119 . Another issue: DAC8760 reuires a SPI, ADS5560 requires a SPI for programming, ADS5560 also requires CMOS parralel output or DDR LVDS output,...
View ArticleForum Post: RE: ADC12D1000: Test pattern in non-demux mode
Thanks Christophe I'll try to gather some comparative data tomorrow to verify what should be happening. Best regards, Jim B
View ArticleForum Post: TSW14J56EVM: Save data capture
Part Number: TSW14J56EVM Good morning Is there a continuous way to save raw data that comes from TSW14J56EVM from the GUI HSDCpro? Is there a way to do that? I am really interested to save the obtained...
View ArticleForum Post: RE: DAC7750: why are there two TVS diodes?
Hello, Thanks for your reply. L&Y
View ArticleForum Post: ADS1262: Giving Garbage value with other SPI slaves where as...
Part Number: ADS1262 I am interfacing ADS1262 with Arduino mega2560 along with TFT and sd card. When I interface ads1262 with above given slave at that time, sometimes it activate and given output and...
View ArticleForum Post: RE: RD-195 problems
Dear TI, 1. Could you please provide the distributor or suggest the seller from whom we can buy the corrected RD 195 boards ? 2. How can i get my faulty board replaced ? Any contact or agency to whom...
View Article