Forum Post: RE: [tvp7002] vsync issue with 1080p 60fps input
Hayden,Check all registers are set correctly. You can use the setup files from the TVP7002EVM product page located here...http://www.ti.com/tool/tvp7002evmhttp://www.ti.com/lit/zip/slec029Open the...
View ArticleForum Post: RE: ADC12D1800RF Modeling
Hi Jim thank you for your helpful comments. I wish you a successfull year 2014.Best regards,Mahdi
View ArticleForum Post: RE: Video decoder or encoder
This is not a trivial task and there is not a single chip solution available.Things you need to consider...What is the compressed video format coming from the Ethernet?What protocol is the video being...
View ArticleForum Post: RE: ADC12D1800RFRB/NOPB evaluation board - USB and FPGA speed issue
Hi Marjorie,I currently have the ADC12D1800RFRB connected to a Xilinx ML-605. Your post states that TI has firmware that supports this connection "to make a deeper memory capture." I would like to...
View ArticleForum Post: RE: audio fore & back conversion
Hi Arjun,With your system, the TLV320AIC3101 would probably not be the best device.Here is my recommendation using devices from TI's audio portfolio (as your application is audio). From the output of...
View ArticleForum Post: RE: coils configuration
Hello Francisco,Apologies for the delayed response!Yes, detection of the pin-like objects is certainly possible, but we do not have anything specific on the topic.General guideline is that you want to...
View ArticleForum Post: RE: Unable to get ADS1298 to connect to computer via USB
Greg,actually I experienced now the same phenomena using Windows 7 64 bit. In case a solution is available by now, please be so kind to send me a hint? Otherwise I would appreciate to receive the...
View ArticleForum Post: RE: ADS1274 Channel failure
Can you share a schematic or provide more details of the connection/circuit?
View ArticleForum Post: LDC1000 CAN BE USED IN DOOR FRAME METAL DETECTOR OR NOT
Can I use LDC1000 in Door Frame Metal Detector for metal detection.Because I am in doubt ,the size of coil used in door frame will be large.Will it work accurately in this application??Please suggest me.
View ArticleForum Post: RE: ADS1278EVM
Please use the information in SBAU197; the other information is available to support previous EVM version only.Please use attached zip files for gerbers.In terms of the user guide, the only table that...
View ArticleForum Post: RE: TLVAIC3101 microphone detection
Hi John,MicDet will not work with the way your hardware is configured. As explained in app note SLAA454, in all modes, whether detecting speakers or microphones, MicDet works by measuring the DC...
View ArticleForum Post: RE: ADS1226 Flow
Hi Alex,It is hard to read the picture, so I can't verify the timing. Can you attach the original logic analyzer plot as a picture file that has better resolution? Once we verify what is happening we...
View ArticleForum Post: RE: Incorrect readings from the ADS1110
Hi Bunnarong,I'm not sure what you are expecting to see with the circuit as shown. If you consider the virtual short of the op amp between pins 2 and 3, with the positive input grounded, pin 2 will...
View ArticleForum Post: RE: DAC7678 Channel-F problem
Hello Andres,I apologize for my delayed response - I was out of office on holiday since December 20th.Are you still debugging this problem?One technique that is sometimes helpful in debugging...
View ArticleForum Post: RE: ADS1298 Single-Ended Input Range
Hi Nate, Are you referring to the internal PGA of the ADS1298, or some external amplifier that the customer is using?Keep in mind that what's really important here is that your input signal to the ADC...
View ArticleForum Post: RE: LM49352 Initiailization Code
We have inexpensive EVMs for the TLV320AIC3120 codec, which has similar functionality.
View ArticleForum Post: RE: ADS1298ECG-FE Shield Driver
It has become clear to me, why the RLDOUT signal needs to be out of phase for Driven Right Leg.The ADS1298ECGFE users guide describes in chapter 4.8.2. how to set the jumper J15 and J17 to get an...
View ArticleForum Post: RE: I don't recommend OMAP-L137 board because of its poor audio...
Hi Jack,I think you are looking at the out-of-band noise in the scope shot. We do all of our testing with the Audio Precision which is the benchmark for audio testing. We can easily hit the datasheet...
View ArticleForum Post: RE: AIC3106 codec serious problem on OMAP-L137 platform
Hi Jack,I think you are looking at the out-of-band noise in the scope shot. We do all of our testing with the Audio Precision which is the benchmark for audio testing. We can easily hit the datasheet...
View ArticleForum Post: RE: ths8200 720P60HZ color bar never appear,but 1080P is OK,why?
Try clearing bit 7 of register 0x03.Not sure beyond this.BR,Steve
View Article