Clik here to view.
Forum Post: RE: idle-channel noise of ADS62C17
Hi, matt;Please see following:those are 16384 samples and FFT by matlab pwelch.Best Regards, Donald
View ArticleForum Post: RE: TLV320AIC10
Hi Hartl,Hope you had a look at the description of experiments I had done. I am still waiting to improve the voice quality in our design. Please help me out with this. We have used PCM 3500 earlier, it...
View ArticleForum Post: RE: TLV320AIC3106 concurrent Multiple channel capture(record)
Hi D. Hartl,Thanks for replying.I am able to mix L1L, L2L and L1R together and read the conversion result on the ADC channels.But the resultant is the mixed signal of all these in a single file.we are...
View ArticleForum Post: RE: TVP7002 video horizontal shaking
Hi Steve,Very thanks for your help.It's useful for me. Thanks a lot.BRSteven
View ArticleForum Post: RE: TSW1400EVM Source Code?
Hi Matt,Many thanks for the help. I would really appreciate it.Regards,Marcinski
View ArticleClik here to view.
Forum Post: RE: AMC7812 can't i2c bus how use it? example code..
Howdy Sungjin,I would make certain that pin12 (SPI/I2C) pin is "low" enabling I2C mode. If A0/A1/A2 are ground, then the slave address will be the 7bit binary 1100001.I've copied an image for an I2C...
View ArticleForum Post: Power Consumption / Better recommendation of TLV320xxx
Hi team,I have a MM customer in the Bay Area who is concerned about the power consumption of these TI parts in comparison to Wolfson. Please let me know if the numbers are what they seem to be, and or...
View ArticleForum Post: Problem with DAC348x GUI
I just installed the DAC348x GUI, but there seems to be a problem:The fonts appear too large (see attached image).Is this a known problem?Regards,Arne
View ArticleForum Post: RE: lmp90100 layout
Hello,Are you able to open gerber files? If not I can make a screen capture of the layers and send it to you.Mike
View ArticleClik here to view.
Forum Post: RE: ADS8528: Issue Writing to the Configuration Register
Hello,I have attached a logic analyzer output below. I decided to send just C800083FF and not 880083FF. I don't see the configuration value in output. The first data item 9001 doesn't seem right...
View ArticleForum Post: RE: Problem with LMP90100 in single scan mode.
Hi Mike,Thanks - My aim is to synchronize each conversion to an external source. I've taken your advice and run the ADC in ScanMode2. I'm also keeping it in Active mode so IB1&2 are always...
View ArticleForum Post: ADS5294EVM compatible with TSW1400EVM?
I want to use the ADS5294 eval module, and it lists the TSW1250EVM deserializer for interfacing. Butthe page for the TSW1250EVM recommends using the TSW1400EVM deserializer but does not listthe...
View ArticleForum Post: ADS8504 internal voltage reference
The TI analog to digital converter, ADS8504IBDW is used in an application where the device is connected to use the internal voltage reference. In the datasheet, there is a note that states: (8) The...
View ArticleForum Post: RE: overclocking ADC12D1800RF
Hi KrisWe can't endorse overclocking of our ADC products. Performance, operation and reliability are only covered for the rated operating conditions as specified in the product datasheet.The fastest...
View ArticleForum Post: RE: Representing captured data in sine wave form
Hi SyedWavevision applies some formatting/parsing to the raw data transferred from the board. I think that is probably the issue. I'll track down the details of how the data is handled for that board...
View ArticleForum Post: RE: ADC12D1800RF Modeling
Hi MahdiWe have received your questions and are working to put together the answers.Sorry for the delay.Best regards,Jim B
View ArticleForum Post: RE: Summing Two 16-Bit DACs for 24-bit Resolution
Hello Kevin,Thanks for the replies - I am discussing with the powers that be now - will let you know.Regards,John
View ArticleForum Post: RE: idle-channel noise of ADS62C17
Hi, Matt;Attached is the raw datas.Tahnk you!Regards,Donald(Please visit the site to view this file)(Please visit the site to view this file)(Please visit the site to view this file)(Please visit the...
View Article