Forum Post: RE: DAC39J84 questions
Hi Mark, We are looking into this, will respond as soon as we can. Regards, Neeraj Gill
View ArticleForum Post: RE: TLV320AIC3262 register settings
Hi, Ito-san, I will take a look at this and I will answer as soon as possible. Best regards, Luis Fernando RodrÃguez S.
View ArticleForum Post: ADS8329, No output using SPI
Hello, I am having trouble reading data from ADS8329 using the SPI protocol. The DSP I am using is TMS320C6657 . I have connected SDO, SDI, CS, SCLK to the DSP board. My VA and Vref is 3.3V, VBD is 3V,...
View ArticleForum Post: RE: ADS1291 Power Down
I Tom, yes i had to write the registers every time i power the ADS1291 back on, otherwise it works with its default registers value. So reset happens before it goes power down.
View ArticleForum Post: RE: ADS1299 Circuit problem
Hi, We checked the values of VCAP terminals. It's as follows VCAP 1 = 1.2V VCAP 2 = 2.5V VCAP 3 = 6.8 V VCAP 4 = 285.3 mV And powers : DVDD - 3.34V AVDD - 4.92V
View ArticleForum Post: RE: TSW54J60/ADS54J60 interleaving correction behaviour at fs/4
Martin, Which path are you using on the EVM? What is the gain setting if you are using the LMH6401 path? You mentioned a 50MHz BW input signal? Was this multi-tone? If so, how many? What is the...
View ArticleForum Post: ADS1278 Evaluation Module : How to interface it with Raspberry Pi...
Hi, I want to capture 2 analog signals (say voltage and current) simultaneously using ADS1278 evaluation module and send it to Raspberry Pi via SPI interfacing. I need to capture the signals...
View ArticleForum Post: RE: what kind of Inductor use for cufflink Power in EEG board use...
I sorry, cufflink mean using inductor to make another power. In VietNam we call it is cufflink power. Thanks for supportion, i have choose best inductor.
View ArticleForum Post: RE: ADS1299 Circuit problem
May be you solder reverse capacitor. I suggest you should measure the current of your circuit
View ArticleForum Post: RE: ADS1299 Circuit problem
We have connected the negative terminals of all the electrolytic capacitor towards the ground. Isn't that correct?
View ArticleForum Post: ADS1220: is there any buffer (for sending data over SPI) inside...
Hi, I am building a really simple data collection system using two sensors (one of the two is ADS1220 ), Bluetooth module, and Arduino UNO R3. The other sensor generates six digital data (2-byte each)...
View ArticleForum Post: About TLV320AIC3254
Dear Sirs TLV320AIC3254 : How to calculate the AGC Iow-pass filter frequency? Thanks BRS Nat
View ArticleForum Post: RE: TLV320AIC3262 register settings
Luis-san, Thanks for your reply. I am waiting for your answer. Best regards, Akio Ito
View ArticleForum Post: RE: ADC1256 stability
Hi Chris, Thanks for the hints. BUFEN was enabled, we checked this earlier. The flat regions on the plots are because we had a sleep() between the loop iterations, so these flat sections are just...
View ArticleForum Post: RE: AMC6821 Reset I2C Hanging the Bus by Holding SDA Low
Hi Matt, >Can you please describe the other case you are referring to? The following situation is considered. 1. Host processor is reading I2C data from the FAN controller IC. 2. By some reasons,...
View ArticleForum Post: RE: Sample Source Code for ADS8688 ADC
Hi, Could you please send me the reference source code, that will help to me. My mail id is: sravan.rikka@hbl.in
View ArticleForum Post: RE: Sample Source Code for ADS8688 ADC
Dear Mr Li Thank you very much for your help. C code is fine I will be able to port for AVR. My e-mail is reyah@medcotas.com , or reyahabd@aol.com . Sorry about the delay in my answer. Best Regards Reyah
View ArticleForum Post: RE: ADS7852 Freeze convert output at Immunity test
Hi Jose, Thank you for your support. I explained about latch-up , then my customer agree with this my answer. I close this question. Thanks Best regards, Shimizu
View Article